- Issue 4,1991 Table of Contents
-
1991(4).
Abstract:Study on the development of Nd-Fe-B permanent-magnet material and its major applications are presented in this paper.
-
Qu Xuanhui , Huang Baiyun , Lu Haibo , Huang Peiyun
1991(4):3-14.
Abstract:In this paper, the development of TiAl ordered alloys is briefly introduced. The research work carried on both at home and abroad to overcome their brittleness at room temperature and poor formability is systematically reviewed. The future tendency for ordered TiAl is outlined finally
-
1991(4):15-25.
Abstract:The Current status of physical property testing techniques for metals in China is described in this paper. Referring to the requirements of material development and the tendency of physical property testing abroad, the author has discussed the main trend in this area in China.
-
1991(4):26-30.
Abstract:The definition and the meaning of microstructure and magnetic properties of rare-earth permanent magnet materials are demonstrated. Based on the nucleation behaviour and the propagation behaviour of the reversed domain walls during magnetization reversal, the current status of the interrelatic between microstructure and magnetic properties are briefly reviewed. For a better understanding of (?) interrelation, it is suggested that the numerical simulation method should be applied to study (?) magnetization reversal process.
-
1991(4):31-35.
Abstract:采用TEM、SEM、X射線衍射、顯微硬度測盛等方法,研究了混合稀土對6063合金陽極氧化膜結構和某些性能的影響。實驗結果表明:當合金成分和生產工藝合理、稀土含最適當(0.2wt%左右)時,加入混合稀土能使6063合金陽極氧化膜更加致密、光潔,密度增大,顯微硬度值提高。
-
Yan Xuebai , Li Zhenghua Li Xuanming , Gao Wen zhu
1991(4):36-45.
Abstract:The effect of the rolling technique of Ti/Al clad sheet on the bonding strength of it after rolling and the morphology of the peeled surface is investigated The results show that the deformation extent of Ti is a dominant factor for bonding strength and morphology of the peeled surface. Aluminium temperature in rolling process also has an important impact on bonding. It is found that three bonding mechanisms coexist during the process.
-
Tang Xiande Zhou Lian Xiong Shougao Wang Keguang Yang Jianchao Wang Tiancheng Wu Xiaozu
1991(4):46-51.
Abstract:報道了采用熔融慢冷工藝制備具有織構生長的YBCO體材的方法。較詳細地闡述了粉末燒結YBCO坯料在1100℃下的熔融分解和隨后通過包晶反應溫度及附近溫區的緩慢冷卻速度對織構生長的影響,還報道了采用熔融慢冷工藝制備的YBCO體材的臨界電流密度。結果表明,熔融慢冷工藝是一種制備具有高J_c值的YBCO體材的有效方法,采用這種工藝方法已獲得臨界電流密度達63405A/cm~2(77K,1T。H∥ab面)的YBCO體材樣品。
-
1991(4):52-55.
Abstract:The application of computer simulation technique in reaction sintening of silicon nitride ceramics is demonstrated by study the effect of computer simulated partical shapes and sizes of the ultrafine silicon powder on the coordination numbers of the partical is powder compact.
-
Li Yuanxi Zhao Fengqin Liu Yanchang
1991(4):56-60.
Abstract:Through the experiment of preparing stainless steel porous filter by sintering compacted water atomized 0Cr18Ni9 powder in vacuum or pure hydrogen, an empirical formular for the relation between average partical size of the powder and maximum pore size in bubble test is suggested. The effects of different partical size forming pressure and addictives on the porosity, maximum pore size, relative permeability coefficient and tensite strength of the porous stainless steel filter are investegated. The developed filter rings have been put into batch production and obvious economical benefits have been achieved.
-
1991(4):61-64.
Abstract:Anodes for cathodic protection are divided into sacrifical anodes and impressed current anodes. This peper recommendes mainlg on impressed current anode materials and anode reactions in cathodic protection, Alsothrough comparison of the characteristics of graphite, silicon-chromium-iron, p latinized Ti/Nb, mixed metal oxides are hopeful anode materials for impressed current cathodic protection.
-
1991(4):65-69.
Abstract:本試驗研究了鎢與硫氰酸鹽生成有色配合物的條件,制訂了測定鋯及鋯合金中雜質鎢的方法。在H_2SO_4-HCl介質中用氯化亞錫加熱處理還原鎢到五價,加入KCNS顯色,在400nm波長處測量吸光度以測定鎢。本方法適用于鋯及其合金中0.002%以上鎢的測定。其加料回收率在95%—105%。樣品測定結果重現性好,變異系數不大于4%。
-
Cai Jinyu , Yin Guoping Su Yinghao
1991(4):73-76.
Abstract:The structure and specifications for agitator made of Mo alloy clad with Pt Rh, as well as the fabrication process and the reward of using the products are presented. The result reveals that home-made aginators are competitive with Japanese ones.
-
1991(4):77-80.
Abstract:Applications of Ti materials in vacuum salt refining and salt chemical industries. as well as obtained economical and social benefits are persented in this paper.
