最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
形變熱處理工藝參數對冷軋態鎳基高溫合金晶界特征分布演變的影響
作者:
作者單位:

山東科技大學

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金項目（面上項目，重點項目，重大項目）：51804187 ， 51904176；,中國博士后科學基金：2019M662400；青島博士后應用研究項目；山東省重點研發計劃：2019GGX104009


Influence of thermal-mechanical processing parameters on grain boundary character distribution evolution in a cold-rolled Ni-based superalloy
Author:
Affiliation:

Shandong University of Science and Technology

Fund Project:

The National Natural Science Foundation of China: 51804187 and 51904176; ,China Postdoctoral Science Foundation: 2019M662400; Qingdao post-doctoral researcher applied research programs; The key technology research and development program of Shandong : 2019GGX104009.

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    本文研究了不同形變熱處理工藝參數對冷軋態鎳基高溫合金中晶界特征分布演變的影響。結果表明，在退火處理過程中，生長事故模型是靜態再結晶(SRX)晶粒中新Σ3晶界形成的主要機制。隨著退火時間和退火溫度的增加，晶界遷移時間延長，晶界遷移速度加快，從而增加了生長事故的發生頻率，促進了Σ3晶界的形成。此外，隨著應變的增加，Σ3晶界的比例先減小后增大。在冷軋變形量為0.1和0.7時，Σ3晶界的比例均可達到60%左右，這與大晶粒團簇的形成密切相關。此外，本文還詳細分析了不同工藝參數下，Σ1晶界、共格Σ3晶界、非共格Σ3晶界、Σ9晶界、Σ27晶界和隨機晶界的演變規律。

    Abstract:

    The influence of thermal-mechanical processing (TMP) parameters on the grain boundary character distribution evolution in a cold-rolled Ni-based superalloy was studied. During annealing treatment, growth accident model was considered to be the main mechanism for the formation of new Σ3 boundaries in the SRX grains. With the increasing annealing time and temperature, there was more time for grain boundary migration and the grain boundary migration was faster at the higher annealing temperature, which could stimulate the formation of Σ3 boundaries by increasing the frequency of growth accidents. In addition, the fraction of Σ3 boundaries decreased firstly with the increasing strain, and then increased again. At the strains of 0.1 and 0.7, the fractions of Σ3 boundaries reached around 60%, which was related to the well development of large grain-clusters. Besides that, the evolution of Σ1 boundaries, coherent Σ3 boundaries, incoherent Σ3 boundaries, Σ9 boundaries, Σ27 boundaries, and random boundaries were also analyzed in detail.

    參考文獻
    相似文獻
    引證文獻
引用本文

張弘斌,張成才,韓寶坤,高魁東,李輝平,秦升學,劉杰,王艷,張鵬,周海萍.形變熱處理工藝參數對冷軋態鎳基高溫合金晶界特征分布演變的影響[J].稀有金屬材料與工程,2020,49(11):3683~3691.[Hongbin Zhang, Chengcai Zhang, Baokun Han, Kuidong Gao, Huiping Li, Shengxue Qin, Jie Liu, Yan Wang, Peng Zhang, Haiping Zhou. Influence of thermal-mechanical processing parameters on grain boundary character distribution evolution in a cold-rolled Ni-based superalloy[J]. Rare Metal Materials and Engineering,2020,49(11):3683~3691.]
DOI：10.12442/j. issn.1002-185X. E20200007

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2020-03-04
  • 最后修改日期:2020-05-18
  • 錄用日期:2020-05-27
  • 在線發布日期: 2020-12-09
  • 出版日期: