最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
固溶處理后預變形對 Ti-6Al-4V Alloy時效行為和機械性能的影響
作者:
作者單位:

西南石油大學材料科學與工程學院

作者簡介:

通訊作者:

中圖分類號:

基金項目:

福建省材料基因重點實驗室開放課題（廈門大學），廣西省信息材料重點實驗室開放基金（桂林電子科技大學），四川省高等學校油氣田材料重點實驗室開放基金（西南石油大學，X151518KCL23）


Effect of Pre-deformation on the Aging Behavior and Mechanical Properties of Ti-6Al-4V Alloy
Author:
Affiliation:

1.School of Materials Science and Engineering,Southwest Petroleum University;2.Sichuan,China;3.College of Materials and Fujian Provincial Key Laboratory of Materials Genome,Xiamen University;4.Fujian,China;5.Guangxi Key Laboratory of Information Materials,Guilin University of Electronic Technology;6.Guangxi,China

Fund Project:

This work was supported by the open fund of Fujian Provincial Key Laboratory of Materials Genome (Xiamen University), and Guangxi Key Laboratory of Information Materials (Guilin University of Electronic Technology), P.R. China, and Scientific Research Foundation and Opening Foundation (X151518KCL23) of Southwest Petroleum University.

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    本文研究了固溶處理后預變形對Ti-6Al-4V合金時效行為和機械性能的影響。結果顯示在940 °C 和 955 °C固溶處理后進行預變形，可以提高時效過程中第二相α的析出。在940 °C固溶處理后，隨著預變形量的增加，時效處理后第二相α含量增加，α相尺寸減小，合金的強度和硬度增加。在時效處理之前進行預變形可以明顯提高合金的拉伸強度和硬度，也能同時保持比較好的韌性。相對固溶溫度為940 °C來說， Ti-6Al-4V合金在955 °C固溶處理后進行預變形，對于提高合金的強度和硬度的效果不顯著。本文采用掃描電鏡對不同預變形和時效處理后的合金斷口形貌進行了分析。

    Abstract:

    The effects of pre-deformation on the aging behavior and mechanical properties of Ti-6Al-4V alloy were studied. Results show that the addition of pre-deformation after the solution process at 940 °C and 955 °C is beneficial in promoting the precipitation of the secondary α phase during the aging of Ti-6Al-4V alloy. When solution temperature was 940 °C, the content of the secondary α phase increased with an increase in pre-deformation amount, its size decreased, and the strength and hardness of the alloy increased monotonously after aging. The tensile strength and hardness of Ti-6Al-4V alloy after aging were evidently higher with pre-deformation than without pre-deformation. Simultaneously, excellent plasticity was maintained. In the case with added pre-deformation, a solution temperature of 955 °C slightly improved the strength and hardness of Ti-6Al-4V alloy compared with a solution temperature of 940 °C. Scanning electron microscopy examinations indicate that the fracture modes of all aged alloys with varying pre-deformation degrees are ductile fracture.

    參考文獻
    相似文獻
    引證文獻
引用本文

王書亮,付朝政,陳雨婷,劉麗,付春艷,黃藝雄,向定漢,蔣小松.固溶處理后預變形對 Ti-6Al-4V Alloy時效行為和機械性能的影響[J].稀有金屬材料與工程,2020,49(7):2198~2206.[Wang Shuliang, Fu Chaozheng, Chen Yuting, Liu Li, Fu Chunyan, Huang Yixiong, Xiang Dinghan, Jiang Xiaosong. Effect of Pre-deformation on the Aging Behavior and Mechanical Properties of Ti-6Al-4V Alloy[J]. Rare Metal Materials and Engineering,2020,49(7):2198~2206.]
DOI：10.12442/j. issn.1002-185X. E20190045

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2019-03-30
  • 最后修改日期:2019-07-01
  • 錄用日期:2019-07-24
  • 在線發布日期: 2020-08-31
  • 出版日期: