最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
C/C復合材料與Invar合金釬焊接頭組織性能研究
作者:
作者單位:

合肥工業大學材料科學與工程學院

作者簡介:

通訊作者:

中圖分類號:

基金項目:

安徽省自然科學基金


Microstructure and mechanical properties of C/C composite/Invar alloy joints brazed with Cu-Sn-Ti alloy
Author:
Affiliation:

Fund Project:

Anhui Provincial Natural Science Foundation

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    C/C復合材料是一種重要的航空航天和核結構材料，實現其與金屬材料的連接可以克服其成本高和成型加工困難的問題。本文采用Cu-Sn-Ti活性釬料釬焊C/C復合材料與Invar合金，研究了釬焊溫度和保溫時間對接頭組織、剪切強度和斷裂行為的影響。結果表明，在C/C復合材料一側，Cu-Sn-Ti與C/C形成TiC反應層并實現連接，同時Cu-Sn-Ti會滲透進C/C復合材料中，形成凹凸不平的釘扎界面并強化接頭；在Invar合金一側，Cu-Sn-Ti與其相互溶解擴散并發生反應，形成良好界面結合；釬焊接頭組織結構為Invar合金/Cu(s,s)+Fe2Ti+Ni3Ti+Ti6Sn5/Fe2Ti+CuTi+Cu3Sn/TiC+Cu(s,s)/C/C復合材料。在釬焊溫度為930 ℃保溫10 min時，接頭剪切強度最高，為61 MPa，明顯高于目前報道的C/C復合材料與金屬的釬焊連接強度。

    Abstract:

    C/C composites are the important structure materials for aerospace and nuclear applications. Realizing the joining of C/C composite to metal materials can overcome the drawbacks of high cost and hard-to-forming difficulties of C/C composite. In this paper, C/C composite and Invar alloy were brazed with active Cu-Sn-Ti filler alloy. The effects of brazing temperature and holding time on the microstructure, shear strength and fracture behavior of brazed joints were investigated. The results showed that, on the side of C/C composite, Cu-Sn-Ti filler reacted with C/C composite to form a TiC reaction layer. In addition, Cu-Sn-Ti filler would penetrate into the C/C composite, which formed a zigzag interface that strengthened the joint. On the side of Invar alloy, Invar alloy dissolved into Cu-Sn-Ti form a good interface metallurgical bonding. The interfacial microstructure of brazed joint was determined to be Invar alloy/Cu(s,s)+Fe2Ti+Ni3Ti+Ti6Sn5/Fe2Ti+CuTi+Cu3Sn/TiC+Cu(s,s)/C/C composite. The maximum shear strength of the joint of 61 MPa, which is significantly higher than the strength reported in previous studies, was obtained at brazing temperature of 930 ℃ and the holding time was 10 min.

    參考文獻
    相似文獻
    引證文獻
引用本文

潘蘇燕,鐘志宏,宋奎晶,梁水保,吳玉程. C/C復合材料與Invar合金釬焊接頭組織性能研究[J].稀有金屬材料與工程,2024,53(8):2232~2240.[Pan Suyan, ZHONG ZHIHONG, Song Kuijing, Liang Shuibao, Wu Yucheng. Microstructure and mechanical properties of C/C composite/Invar alloy joints brazed with Cu-Sn-Ti alloy[J]. Rare Metal Materials and Engineering,2024,53(8):2232~2240.]
DOI：10.12442/j. issn.1002-185X.20230387

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2023-06-18
  • 最后修改日期:2023-07-30
  • 錄用日期:2023-08-24
  • 在線發布日期: 2024-08-20
  • 出版日期: 2024-08-08