最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
選區激光熔化Zr改性Al-Si-Mg合金組織和力學性能
作者:
作者單位:

1.江蘇科技大學;2.江蘇昆山國力電子科技股份有限公司

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金青年基金(Nos. 52001140和51801079)資助


Microstructure and mechanical properties of Zr modified Al-Si-Mg alloy produced by selective laser melting
Author:
Affiliation:

1.Jiangsu University of Science and Technology,Zhen’jiang;2.Kunshan Guoli Vacuum Electric Co.,Ltd.

Fund Project:

國家自然科學基金青年基金(Nos. 52001140和51801079)資助

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    針對選區激光熔化（SLM）高Mg含量AlSiMg3合金成形性差的缺點，通過Zr進行合金化，系統研究了工藝參數對SLM成形高Mg含量Al-Si-Mg-Zr合金的成形性及時效處理對合金組織和力學性能的影響。結果表明，SLM成形Al-Si-Mg-Zr合金的熔池邊界處形成了大量的細小等軸晶，從而有效避免了樣品在成形過程中裂紋的產生，增加了樣品的SLM成形性，不同激光功率和激光掃描速度下獲得樣品的孔隙率均低于0.3%。拉伸測試結果表明，成形態樣品的屈服強度（YS）為426±8 MPa，極限抗拉強度（UTS）為464±12 MPa。經165 ℃時效處理后，由于α-Al晶粒內部納米強化相的增多，樣品的強度增加明顯，時效樣品的最大YS和UTS分別為482±11 MPa和522±10 MPa。本研究獲得SLM成形Al-Si-Mg-Zr樣品的強度高于目前商用的SLM成形Al-Si-Mg合金。

    Abstract:

    The present study is devoted to research the effect of process parameters on processability, and aging treatment on microstructure and mechanical properties of selective laser melting (SLM) high Mg-content Al-Si-Mg-Zr alloy. The results show that alloy forms a large number of fine equiaxed grains at the boundary of the molten pool, which can avoid the generation of cracks during the SLM forming process and increase the processability of the sample. The porosity of the samples obtained under different process conditions is less than 0.3%. The yield strength (YS) and ultimate tensile strength (UTS) of the as-built samples are 426 ± 8 MPa and 464 ± 12 MPa respectively. After aging treatment, due to the increase in the number of nanoparticles embedded in α-Al cells, the strength of the sample increases obviously. The maximum YS and UTS of aged samples reach 482 ± 11 MPa and 522 ± 10 MPa, respectively. The strength of present samples is much higher than that of commercial SLM-formed Al-Si-Mg alloy.

    參考文獻
    相似文獻
    引證文獻
引用本文

呂洪偉,張志杰,羅金杰,耿遙祥,鞠洪博,喻利花,許俊華.選區激光熔化Zr改性Al-Si-Mg合金組織和力學性能[J].稀有金屬材料與工程,2023,52(3):1087~1093.[Lu Hongwei, Zhang Zhijie, Luo Jinjie, Geng Yaoxiang, Ju Hongbo, Xu Junhua, Yu Lihua. Microstructure and mechanical properties of Zr modified Al-Si-Mg alloy produced by selective laser melting[J]. Rare Metal Materials and Engineering,2023,52(3):1087~1093.]
DOI：10.12442/j. issn.1002-185X.20220081

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2022-01-26
  • 最后修改日期:2022-05-25
  • 錄用日期:2022-06-16
  • 在線發布日期: 2023-04-07
  • 出版日期: 2023-03-24