最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
三層復合板鋁/鎂合金/鋁FSW接頭的微觀組織與抗拉強度
作者:
作者單位:

太原科技大學 材料科學與工程學院

作者簡介:

通訊作者:

中圖分類號:

TG 406

基金項目:

山西省重點研發計劃（高新技術領域）（201903D121054）；NSFC-山西煤基低碳聯合基金（重點支持項目）（U1910213）；山西省高等學校科技創新項目（2019L0621）


Microstructure and Tensile Strength of Aluminum/Magnesium Alloy/Aluminum FSW Joint of Three-Layer Composites
Author:
Affiliation:

1.School of Materials Science and Engineering, Taiyuan University of Science and Technology;2.Taiyuan University of Science and Technology

Fund Project:

Shanxi Province Key R&D Program Project (High-tech Field) (201903D121054); Shanxi Province Higher Education Science and Technology Innovation Project (2019L0621)

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    摘 要:在不同焊接速度下進行了三層復合板Al/AZ31/Al 攪拌摩擦焊接（FSW）工藝試驗，并觀察分析其接頭成形顯微組織和拉伸性能。結果顯示：在實驗優化的工藝參數下，焊縫接頭成形較好，其內部呈層狀分布且未發現缺陷；焊核區（NZ）晶粒細化明顯，大角晶界（HAGBs）和再結晶晶粒占比達80%；在焊縫前進側帶狀組織區（BS）和鎂、鋁界面處存在金屬間化合物（IMC），主要為Al3Mg2和Al12Mg17；隨焊速的增加，焊接接頭的抗拉強度先增大后減小，在v=100 mm/min時焊核區鋁層晶粒平均尺寸為1.75 μm，接頭抗拉強度達到最大87.3 MPa，是母材的50.8%。

    Abstract:

    Abstract: The friction stir welding (FSW) process tests of three-layer composite plate Al/AZ31/Al at different welding speeds were carried out, and the joint forming, microstructure and tensile properties were observed and analyzed. The results show that under the optimized process parameters, the welded joint is well formed, and its internal distribution is layered, and no defects are found. The grain refinement in nugget zone (NZ) is obvious, and the large angle grain boundaries (HAGBs) and recrystallized grains account for 80%. There is intermetallic compound (IMC) in the banded structure area (BS) on the forward side of the weld and the interface between magnesium and aluminum, which is mainly composed of Al3Mg2 and Al12Mg17. With the increase of welding speed, the tensile strength of welded joint first increases and then decreases. When v=100 mm/min, the average grain size of the aluminum layer in the weld nugget area is 1.75 μm, and the tensile strength of the welded joint reaches the maximum 87.3 MPa, which is 50.8% of the base metal.

    參考文獻
    相似文獻
    引證文獻
引用本文

趙菲,王康.三層復合板鋁/鎂合金/鋁FSW接頭的微觀組織與抗拉強度[J].稀有金屬材料與工程,2022,51(3):1047~1054.[Zhao Fei, Wang kang. Microstructure and Tensile Strength of Aluminum/Magnesium Alloy/Aluminum FSW Joint of Three-Layer Composites[J]. Rare Metal Materials and Engineering,2022,51(3):1047~1054.]
DOI：10.12442/j. issn.1002-185X.20210899

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2021-10-17
  • 最后修改日期:2021-12-13
  • 錄用日期:2022-01-28
  • 在線發布日期: 2022-04-06
  • 出版日期: 2022-03-30