-11 m3/N·m），以及較高的硬度（HK0.05=38 000 MPa）和膜-基結合強度（LC2=53±1 N）。多層涂層相鄰層之間形成了較多的界面，有助于提高多層涂層的硬度和耐磨性。切削試驗結果顯示，當切削磨損標準VB=0.2時，AlCrN/AlCrVN-6涂層具有較高的硬度和耐磨性，最長的切削長度為7.4 m。"/>

最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
不同雙層結構AlCrN/AlCrVN多層涂層的力學和磨損性能
作者:
作者單位:

1.安徽工業大學 先進金屬材料綠色制備與表面技術教育部重點實驗室，安徽 馬鞍山 243000;2.安徽工業大學 現代表界面工程研究中心，安徽 馬鞍山 243002;3.安徽工業大學 材料科學與工程學院，安徽 馬鞍山 243002

作者簡介:

通訊作者:

中圖分類號:

基金項目:

the Science Foundation of Anhui Province (Grant no. 1808085QE131), Tribology Science Fund of State Key Laboratory of Tribology (Grant no. SKLTKF18B13). This work was also supported by the Key research and development plan of Anhui Province (Grant no. 1804b06020370)


Mechanical and Wear Properties of AlCrN/AlCrVN Multi-layer Coatings with Different Numbers of Bilayers
Author:
Affiliation:

1.Key Laboratory of Green Fabrication and Surface Technology of Advanced Metal Materials, Ministry of Education, Anhui University of Technology, Maanshan 243000, China;2.Research Center of Modern Surface & Interface Engineering, Anhui University of Technology, Maanshan 243002, China;3.School of Materials Science and Engineering, Anhui University of Technology, Maanshan 243002, China

Fund Project:

Science Foundation of Anhui Province (1808085QE131); Tribology Science Fund of State Key Laboratory of Tribology (SKLTKF18B13); Key Research and Development Plan of Anhui Province (1804b06020370)

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    采用電弧離子鍍的方法制備了不同數目（1、2、4、6）雙層結構的AlCrN/AlCrVN多層涂層，并研究了多層結構對涂層微觀結構、力學、摩擦學和切削性能的影響。結果顯示，沉積態AlCrN/AlCrVN多層涂層主要由固溶(Al，Cr)N組成，優先生長方向為[111]晶向。與其他多層涂層相比，具有6層雙層結構的AlCrN/AlCrVN涂層在高溫下表現出較低的摩擦系數（約0.46）和磨損率（0.15×10-11 m3/N·m），以及較高的硬度（HK0.05=38 000 MPa）和膜-基結合強度（LC2=53±1 N）。多層涂層相鄰層之間形成了較多的界面，有助于提高多層涂層的硬度和耐磨性。切削試驗結果顯示，當切削磨損標準VB=0.2時，AlCrN/AlCrVN-6涂層具有較高的硬度和耐磨性，最長的切削長度為7.4 m。

    Abstract:

    AlCrN/AlCrVN multi-layer coatings with different numbers (1, 2, 4, 6) of bilayers were deposited by arc ion plating method. The effects of multi-layer structure on microstructure, mechanical properties, tribological properties, and cutting performance were investigated. The results show that the deposited AlCrN/AlCrVN multi-layer coatings are mainly composed of solid solution (Al,Cr)N with preferred growth orientation of [111] crystal orientation. Compared with other multi-layer coatings, the lowest coefficient of friction (~0.46), the lowest wear rate of 0.15×10-11 m3/N·m, the highest hardness of HK0.05=38 000 MPa, and coating-substrate bonding strength of LC2=53±1 N can be achieved for AlCrN/AlCrVN multi-layer coating with 6 bilayers at high temperature. The improvement in hardness and wear resistance is due to the formation of more interfaces between adjacent layers. Cutting test results reveal that AlCrN/AlCrVN coating with 6 bilayers has the longest cutting length of 7.4 m under the cutting wear standard condition of flank wear VB=0.2 due to its relatively higher hardness and better wear resistance.

    參考文獻
    相似文獻
    引證文獻
引用本文

Iram Sidra,蔡飛,王建明,房磊琦,張家敏,Ahmad Farooq,張世宏.不同雙層結構AlCrN/AlCrVN多層涂層的力學和磨損性能[J].稀有金屬材料與工程,2022,51(1):74~82.[Sidra Iram, Cai Fei, Wang Jianming, Fang Leiqi, Zhang Jiamin, Farooq Ahmad, Zhang Shihong. Mechanical and Wear Properties of AlCrN/AlCrVN Multi-layer Coatings with Different Numbers of Bilayers[J]. Rare Metal Materials and Engineering,2022,51(1):74~82.]
DOI：10.12442/j. issn.1002-185X.20200803

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2020-10-19
  • 最后修改日期:2020-11-14
  • 錄用日期:2020-11-25
  • 在線發布日期: 2022-02-04
  • 出版日期: 2022-01-28