-1條件下的熱變形行為，利用動態材料模型構建了鈦鋁復合板熱加工圖，并基于熱加工圖進行了鈦鋁復合板熱軋工藝驗證實驗。結果表明：鈦鋁復合板屬于正應變速率敏感材料；在熱加工圖中變形溫度為420~460 ℃、應變速率為1.6~6.3 s-1時，功率耗散效率達到0.64~0.72，該區域?qū)?yīng)的工藝參數適合進行鈦鋁復合板熱軋；熱軋后實驗板材界面結合良好，具有良好的力學性能和鈑金成形性能。鈦鋁復合板在熱軋過程中的變形機制為：變形抗力低、流動快的鋁層在自身發生塑性變形的同時牽引著鈦層一起發生塑性變形，其中鋁層是熱變形，鈦層為冷變形。"/>

最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
鈦鋁復合板熱加工圖及熱軋實驗
作者:
作者單位:

1.東華理工大學 機械與電子工程學院，江西 南昌 330013;2.有研科技集團有限公司 有研金屬?gòu)?fù)材技術有限公司，北京 100088

作者簡介:

通訊作者:

中圖分類號:

TG339

基金項目:

東華理工大學博士科研啟動基金 (DHBK2017123 )


Hot Processing Map and Hot Rolling Experiment of Ti-Al Clad Plate
Author:
Affiliation:

1.School of Mechanical and Electronic Engineering, East China University of Technology, Nanchang 330013, China;2.GRINM Metal Composites Technology Corporation Limited, GRINM Group Corporation Limited, Beijing 100088, China

Fund Project:

East China University of Technology Research Foundation for Advanced Talents (DHBK2017123)

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    采用Gleeble-3500熱模擬試驗機進行高溫等溫壓縮實驗，研究了爆炸焊接鈦鋁復合板在變形溫度為300~500 ℃、應變速率為0.1~10 s-1條件下的熱變形行為，利用動態材料模型構建了鈦鋁復合板熱加工圖，并基于熱加工圖進行了鈦鋁復合板熱軋工藝驗證實驗。結果表明：鈦鋁復合板屬于正應變速率敏感材料；在熱加工圖中變形溫度為420~460 ℃、應變速率為1.6~6.3 s-1時，功率耗散效率達到0.64~0.72，該區域?qū)?yīng)的工藝參數適合進行鈦鋁復合板熱軋；熱軋后實驗板材界面結合良好，具有良好的力學性能和鈑金成形性能。鈦鋁復合板在熱軋過程中的變形機制為：變形抗力低、流動快的鋁層在自身發生塑性變形的同時牽引著鈦層一起發生塑性變形，其中鋁層是熱變形，鈦層為冷變形。

    Abstract:

    The hot deformation behavior of explosive welded titanium-aluminum (Ti-Al) clad plate was studied by isothermal compression tests at 300~500 °C with strain rates of 0.1~10 s-1 on Gleeble 3500 simulated machine. The hot processing map was developed on the basis of experimental data using the principles of dynamic materials model, and the verification experiment of hot rolling process of Ti-Al clad plate was carried out based on the hot processing map. The results show that Ti-Al clad plate is a kind of positive strain rate sensitive material. The efficiency of power dissipation of 0.64~0.72 can be observed at 420~460 °C with strain rate of 1.6~6.3 s-1 in the hot processing map, and the process parameters of this region are suitable for the hot rolling of Ti-Al clad plate. After hot rolling, the interfaces of the Ti-Al clad plates are well bonded, and the plates have excellent mechanical property and good sheet metal forming property. The deformation mechanism of Ti-Al clad plate in the hot rolling process is as follows: the Al layer with low deformation resistance and fast flow can produce plastic deformation, and at the same time it can pull the Ti layer together to produce plastic deformation; in this process, the Al layer is hot deformation while the Ti layer is cold deformation.

    參考文獻
    相似文獻
    引證文獻
引用本文

彭海健,胡捷.鈦鋁復合板熱加工圖及熱軋實驗[J].稀有金屬材料與工程,2021,50(12):4218~4223.[Peng Haijian, Hu Jie. Hot Processing Map and Hot Rolling Experiment of Ti-Al Clad Plate[J]. Rare Metal Materials and Engineering,2021,50(12):4218~4223.]
DOI：10.12442/j. issn.1002-185X.20200700

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2020-09-13
  • 最后修改日期:2021-01-26
  • 錄用日期:2021-03-08
  • 在線發布日期: 2021-12-30
  • 出版日期: 2021-12-24