-1~10 s-1條件下的高溫不連續屈服行為和絕熱溫升效應,并對這兩種同名義成分不同制備工藝的鈦合金進行了對比研究。結果表明：兩種合金不連續屈服的幅度均與應變速率呈正相關關系,并與溫度呈近似負相關關系, 兩種合金中出現的不連續屈服現象符合動態理論。在相同變形條件下,鑄態合金中不連續屈服的幅度更大,其原因是相對于粉末冶金態合金,鑄態合金中的起始位錯密度低,這更有利于晶界處可動位錯的突然增殖與擴展。兩種合金在熱變形中絕熱溫升的大小均隨應變速率的升高而逐漸增大,并隨著變形溫度的升高而逐漸降低。在相同變形條件下,粉末冶金態合金的絕熱溫升效應相比與鑄態合金較弱,這是因?yàn)榉勰┮苯饝B(tài)合金具有較低的變形抗力和較高的協調變形能力。"/>

最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
粉末冶金態與鑄態Ti-5553合金高溫不連續屈服行為和絕熱溫升效應對比研究
作者:
作者單位:

1.長安大學 材料科學與工程學院;2.新西蘭懷卡托大學

作者簡介:

通訊作者:

中圖分類號:

基金項目:

New Zealand Ministry of Business, Innovation and Employment (UOWX1402)


Comparison of Discontinuous Yielding Phenomenon and Adiabatic Temperature Rising of Ti-5553 Alloy Prepared by Powder and Ingot Metallurgy Approaches during Hot Compression
Author:
Affiliation:

1.School of Material Science and Engineering,Chang’an University,Xi’an;2.School of Engineering,University of Waikato,Hamilton ,New Zealand

Fund Project:

New Zealand Ministry of Business, Innovation and Employment (UOWX1402)

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    本文系統地研究了粉末冶金態與鑄態Ti-5553合金在溫度為700 ℃~1100 ℃、應變速率為0.001 s-1~10 s-1條件下的高溫不連續屈服行為和絕熱溫升效應,并對這兩種同名義成分不同制備工藝的鈦合金進行了對比研究。結果表明：兩種合金不連續屈服的幅度均與應變速率呈正相關關系,并與溫度呈近似負相關關系, 兩種合金中出現的不連續屈服現象符合動態理論。在相同變形條件下,鑄態合金中不連續屈服的幅度更大,其原因是相對于粉末冶金態合金,鑄態合金中的起始位錯密度低,這更有利于晶界處可動位錯的突然增殖與擴展。兩種合金在熱變形中絕熱溫升的大小均隨應變速率的升高而逐漸增大,并隨著變形溫度的升高而逐漸降低。在相同變形條件下,粉末冶金態合金的絕熱溫升效應相比與鑄態合金較弱,這是因?yàn)榉勰┮苯饝B(tài)合金具有較低的變形抗力和較高的協調變形能力。

    Abstract:

    Discontinuous yielding phenomenon (DYP) and adiabatic temperature rising (ATR) effect have been investigated in this paper for Ti-5553 (Ti-5Al-5Mo-5V-3Cr) alloys manufactured by powder metallurgy (PM) and ingot metallurgy (IM) approaches based on hot compression testing conducted at the temperature range of 700 °C to 1100 °C and the strain rate range of 0.001 s-1 to 10 s-1. The results show that the magnitude of yield drop exhibits a positive correlation to strain rate but nearly a negative correlation to deformation temperature for both PM and IM alloys, and the occurrences of DYP in the alloys are elucidated by the dynamic theory. IM alloy shows a higher degree of yield drop than PM alloy at the same condition because of low initial dislocation density at as-cast state and the subsequently promoted newly-generated mobile dislocation from grain boundary. Strong positive correlation between ATR effect and strain rate but intensive negative correlation when it subjected to deformation temperature are uncovered for the two alloys. PM alloy shows a lower degree of ATR effect at the same processing condition than IM alloy as a result of its lower deformation resistance and higher deformation compatibility.

    參考文獻
    相似文獻
    引證文獻
引用本文

趙秦陽,陳永楠,徐義庫,Fei Yang, Leandro Bolzoni.粉末冶金態與鑄態Ti-5553合金高溫不連續屈服行為和絕熱溫升效應對比研究[J].稀有金屬材料與工程,2020,49(8):2567~2573.[Qinyang Zhao, Yongnan Chen, Yiku Xu, Fei Yang, Leandro Bolzoni. Comparison of Discontinuous Yielding Phenomenon and Adiabatic Temperature Rising of Ti-5553 Alloy Prepared by Powder and Ingot Metallurgy Approaches during Hot Compression[J]. Rare Metal Materials and Engineering,2020,49(8):2567~2573.]
DOI：10.12442/j. issn.1002-185X.20200090

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2020-02-15
  • 最后修改日期:2020-02-24
  • 錄用日期:2020-03-05
  • 在線發布日期: 2020-09-27
  • 出版日期: