0.2,而760 ℃和800℃條件下時效4 h時出現峰值,分別為385 HV0.2和361 HV0.2。720 ℃、760℃及800 ℃時效條件下不同時效時間對應的抗拉強度最大值分別1153 MPa,1090 MPa和1026 MPa。"/>

最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
不同時效溫度下激光增材再制造IN718合金層的組織與性能研究
作者:
作者單位:

1.浙江工業大學激光先進制造研究院;2.卡爾頓大學機械與航空航天工程系,加拿大 渥太華 KIS B;3.湖南大學

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家重點研發計劃項目(2017YFB1103600),浙江省重點研發計劃聯合技術研發與示范推廣項目(2019C04004),省屬高?；究蒲袠I(yè)務費項目(RF-C2019003)


Microstructure and Properties of Laser Additive Remanufactured IN718 Alloy Treated with Different Aging Temperatures
Author:
Affiliation:

1.Institute of Laser Advanced Manufacturing,Zhejiang University of Technology;2.Department of Mechanical and Aerospace Engineering,Carleton University,Ottawa Ontario,KIS B,Canada

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    研究了不同時效處理對激光增材再制造IN718合金組織及性能的影響。研究表明,時效處理不能改變激光增材再制造IN718合金的外延生長組織特征,但在微觀上能夠影響Laves在枝晶間的含量和形態。在不同時效溫度條件下,隨著時效時間的增加,γ 相逐漸長大并在保溫一定時間后發生γ 相到δ相的轉變,且時效溫度越高,所需時間越短。此外,不同時效溫度下處理后的修復區顯微硬度和抗拉強度隨時間均表現出先增后減的趨勢。720 ℃條件下,顯微硬度在時效16 h時出現峰值410 HV0.2,而760 ℃和800℃條件下時效4 h時出現峰值,分別為385 HV0.2和361 HV0.2。720 ℃、760℃及800 ℃時效條件下不同時效時間對應的抗拉強度最大值分別1153 MPa,1090 MPa和1026 MPa。

    Abstract:

    The effects of aging treatment on the microstructure and properties of laser additive remanufactured IN718 alloy were studied. The results show that the aging treatment can not change the epitaxy growth structure of laser additive remanufactured IN718 alloy, but it will affect the content and morphology of Laves phase. With increase of the aging time, γ phase gradually grows up and changes to δ after holding for a certain time at different aging temperatures. The higher aging temperature, the shorter the time required. In addition, the microhardness and tensile strength of the repaired zone increase firstly and then decrease with holding time at different aging temperatures. The peak value of microhardness is 410 HV0.2 at 720 ℃ for 16 h, 385 HV0.2 and 361 HV0.2 at 760 ℃ and 800 ℃ for 4 h, respectively. The maximum values of tensile strength corresponding to different aging time at 720 ℃, 760 ℃ and 800 ℃ are 1153 MPa, 1090 MPa and 1026 MPa, respectively.

    參考文獻
    相似文獻
    引證文獻
引用本文

張群莉,張杰,李棟,童文華,Liu Rong,宋立軍,姚建華.不同時效溫度下激光增材再制造IN718合金層的組織與性能研究[J].稀有金屬材料與工程,2020,49(5):1785~1792.[Zhang Qunli, Zhang Jie, Li Dong, Tong Wenhua, Rong Liu, Song Lijun, Yao Jianhua. Microstructure and Properties of Laser Additive Remanufactured IN718 Alloy Treated with Different Aging Temperatures[J]. Rare Metal Materials and Engineering,2020,49(5):1785~1792.]
DOI：10.12442/j. issn.1002-185X.20190861

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2019-10-18
  • 最后修改日期:2019-12-29
  • 錄用日期:2020-01-03
  • 在線發布日期: 2020-06-05
  • 出版日期: