最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
焊接溫度和保溫時間對Ni-14Cr-10P-xTi釬料焊接C/C復合材料組織和性能的影響
作者:
作者單位:

中南大學 粉末冶金國家重點實驗室

作者簡介:

通訊作者:

中圖分類號:

基金項目:


Effect of welding temperature and holding time on microstructure and properties of Ni-14Cr-10P-xTi brazing filler C/C composites
Author:
Affiliation:

Powder Metallurgy Research Institute, Central South University

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    用真空熔煉、惰性氣體霧化的方法制備Ni-14Cr-10P金屬粉末，再加入Ti粉和高分子聚合物高速攪拌分散制備了Ni-14Cr-10P-xTi膏狀活性釬料。用制備的焊膏在真空釬焊爐中釬焊C/C復合材料，然后測試了釬焊接頭的剪切強度，采用SEM、EDS、XRD等方法對接頭微觀組織進行了分析。結果表明，在釬焊溫度1000℃，保溫時間30min時，接頭獲得了最高的剪切強度，然后隨著釬焊溫度的上升、保溫時間延長，釬焊接頭強度下降；添加Ti元素加快了釬焊強度隨溫度和保溫時間的增加而下降的速度，結合微觀組織結構，本文對Ti元素加入后釬焊強度隨溫度和保溫時間增加而下降更為迅速的原因進行了分析。

    Abstract:

    Ni-14Cr-10P metal powder was prepared by vacuum melting and inert gas atomization, and then Ti powder and polymer paste were added and stirred at high speed to prepare Ni-14Cr-10P-xTi paste active solder. The C/C composites were welded in the vacuum brazing furnace with the prepared active solder paste, and then the welded joint shear strength was tested. The microstructure and mechanical properties of the joints were investigated by SEM, EDS and XRD. The results show that the strength of the welded joint decreases with the increase of welding temperature and the holding time；The addition of Ti accelerates the decrease of welding strength with temperature and holding time. Combined with the microstructure, the reason why the welding strength decreases with the increase of temperature and holding time after the addition of Ti element is analyzed.

    參考文獻
    相似文獻
    引證文獻
引用本文

易振華,冉麗萍,易茂中.焊接溫度和保溫時間對Ni-14Cr-10P-xTi釬料焊接C/C復合材料組織和性能的影響[J].稀有金屬材料與工程,2020,49(1):361~369.[Yi ZhenHua, Ran LiPing, Yi MaoZhong. Effect of welding temperature and holding time on microstructure and properties of Ni-14Cr-10P-xTi brazing filler C/C composites[J]. Rare Metal Materials and Engineering,2020,49(1):361~369.]
DOI：10.12442/j. issn.1002-185X.20181272

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2018-12-21
  • 最后修改日期:2019-03-25
  • 錄用日期:2019-04-10
  • 在線發布日期: 2020-02-16
  • 出版日期: