最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
熱處理對激光立體成形新型Ti-6Al-6Mo合金顯微組織和硬度的影響
作者:
作者單位:

1.長安大學材料科學與工程學院;2.西北工業大學凝固技術國家重點實驗室

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家重點研發計劃項目(No. 2016YFB0700301, No. 2016YFB1100103), 中國博士后科學基金項目（No. 2016M592731）


Effect of heat treatment on the microstructure and hardness of a novel Ti-6Al-6Mo alloy formed by laser solid forming
Author:
Affiliation:

1.School of Material Science and Engineering,Chang’an University,Xi’an;2.State Key Laboratory of Solidification Processing,Northwestern Polytechnical University,Xi’an

Fund Project:

The National Key Research and Development Program of China (No. 2016YFB0700301, No. 2016YFB1100103), China Postdoctoral Science Foundation (No. 2016M592731)

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    以混合元素粉末為原料,采用激光立體成形(Laser solid forming, LSF)技術制備新型Ti-6Al-6Mo合金。研究了沉積態試樣的顯微組織以及固溶時效處理對合金顯微組織形成及硬度的影響。結果表明,本研究所采用的熱處理制度對原始β晶粒形貌沒有顯著的影響；固溶溫度、固溶時間和固溶后的冷卻方式對原始β晶粒中α相的形貌和尺寸以及LSF Ti-6Al-6Mo合金的顯微硬度均有顯著影響。當時效時間超過4小時后,隨著時效時間的延長,合金的顯微組織和顯微硬度均未產生明顯變化?；诓煌瑹崽幚?xiàng)l件下LSF Ti-6Al-6Mo合金中初生α板條和次生α板條的析出機制及其對β基體的強化作用分析,揭示了熱處理對LSF Ti-6Al-6Mo合金的顯微組織和顯微硬度的影響機理。

    Abstract:

    A novel Ti-6Al-6Mo alloy sample was fabricated by laser solid forming (LSF) using blended elemental powders as raw material. The microstructure of as-deposited sample and the effects of solution and aging treatment on the microstructure and microhardness of LSF Ti-6Al-6Mo alloy were discussed. The results showed that the heat treatment conducted in this study has no significant effect on the morphologies of prior b grains of the alloy. The solution temperature, solution time, and the cooling method after solution treatment have a significant effect on the morphology and size of the α phase in the prior β grains and the microhardness of the LSF Ti-6Al-6Mo alloy. When the aging time exceeds 4 hours, the microstructure and microhardness of the alloy change little with increasing aging time. Based on the analysis of precipitation and strengthening effect of the primary α laths and secondary α laths on the b matrix in LSF Ti-6Al-6Mo alloy under different heat treatment conditions, the influence mechanism of heat treatment on the microstructure and microhardness of LSF Ti-6Al-6Mo was revealed.

    參考文獻
    相似文獻
    引證文獻
引用本文

張鳳英,胡騰騰,譚華,邱瑩,梅敏,楊海歐.熱處理對激光立體成形新型Ti-6Al-6Mo合金顯微組織和硬度的影響[J].稀有金屬材料與工程,2019,48(2):357~365.[Zhang Fengying, Hu Tengteng, Tan Hua, Qiu Ying, Mei Min, Yang Haiou. Effect of heat treatment on the microstructure and hardness of a novel Ti-6Al-6Mo alloy formed by laser solid forming[J]. Rare Metal Materials and Engineering,2019,48(2):357~365.]
DOI：10.12442/j. issn.1002-185X.20180526

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2018-05-22
  • 最后修改日期:2018-06-21
  • 錄用日期:2018-06-27
  • 在線發布日期: 2019-03-15
  • 出版日期: