0.46Cu0.14Zr0.27Ni0.13)1-xSix非晶釬料,研究了添加一定量的Si對釬料非晶形成能力的影響。結果表明,當Si的含量達到0.5%時釬料的非晶形成能力最強,釬料的潤濕面積為3.06 cm2,過冷液相區寬度(?Tx)?Tx=56 ℃,約化玻璃轉變溫度(Trg)Trg=0.5387,液相線溫度為949 ℃。以此非晶合金作為釬料對SiC和TC4進行真空釬焊,所得釬焊接頭剪切強度為80 MPa。Si元素的加入顯著提高了釬料的非晶形成能力。"/>

最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
Si元素對Ti-Cu-Zr-Ni基非晶釬料微觀組織和性能的影響
DOI:
作者:
作者單位:

中國礦業大學材料科學與工程學院,中國礦業大學材料科學與工程學院,中國礦業大學材料科學與工程學院,中國礦業大學材料科學與工程學院,中國礦業大學材料科學與工程學院,中國礦業大學材料科學與工程學院

作者簡介:

通訊作者:

中圖分類號:

基金項目:

中央高?；A(chǔ)研究經費


Effect of Si on the microstructure and performance of Ti-Cu-Zr-Ni-based amorphous filler metal
Author:
Affiliation:

School of Materials Science Engineering,China University of Mining and Technology,School of Materials Science Engineering,China University of Mining and Technology,School of Materials Science Engineering,China University of Mining and Technology,School of Materials Science Engineering,China University of Mining and Technology,School of Materials Science Engineering,China University of Mining and Technology,School of Materials Science Engineering,China University of Mining and Technology

Fund Project:

Fundamental Research Funds for the Central Universities

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    采用電弧熔煉和快冷甩帶工藝制備了(Ti0.46Cu0.14Zr0.27Ni0.13)1-xSix非晶釬料,研究了添加一定量的Si對釬料非晶形成能力的影響。結果表明,當Si的含量達到0.5%時釬料的非晶形成能力最強,釬料的潤濕面積為3.06 cm2,過冷液相區寬度(?Tx)?Tx=56 ℃,約化玻璃轉變溫度(Trg)Trg=0.5387,液相線溫度為949 ℃。以此非晶合金作為釬料對SiC和TC4進行真空釬焊,所得釬焊接頭剪切強度為80 MPa。Si元素的加入顯著提高了釬料的非晶形成能力。

    Abstract:

    The (Ti0.46Cu0.14Zr0.27Ni0.13)1-xSix amorphous filler metal was prepared by arc melting and fast-cooling melt-spinning technologies, and the effect of a certain amount of Si added to the filler metal on its amorphous forming ability was studied. The results show that the filler metal presented the strongest amorphous forming ability when the additive Si reached 0.5%; its wetting area was 3.06 cm2,its supercooled liquid phase region width (?Tx) ?Tx=56 ℃,its reduced glass transition temperature (Trg) Trg=0.5387, and its liquidus temperature was 949 ℃. The vacuum brazing was done for SiC and TC4 using this amorphous alloy as the filler metal, and the shear strength of brazed joint was 80 MPa. The amorphous forming ability of filler metal was improved with addition of Si to the filler metal.

    參考文獻
    相似文獻
    引證文獻
引用本文

委福祥,高鶴,隋艷偉,戚繼球,何業增,孟慶坤. Si元素對Ti-Cu-Zr-Ni基非晶釬料微觀組織和性能的影響[J].稀有金屬材料與工程,2018,47(7):2023~2027.[Wei Fuxiang, Gao He, Sui Yanwei, Qi Jiqiu, He Yezeng, Meng Qingkun. Effect of Si on the microstructure and performance of Ti-Cu-Zr-Ni-based amorphous filler metal[J]. Rare Metal Materials and Engineering,2018,47(7):2023~2027.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2017-12-20
  • 最后修改日期:2017-12-28
  • 錄用日期:2018-01-10
  • 在線發布日期: 2018-10-10
  • 出版日期: