最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
攪拌頭偏移對Ti/Al異種金屬攪拌摩擦焊接頭成形及拉伸強度的影響
作者:
作者單位:

航空制造工程學院 南昌航空大學

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金(51265042)、江西省優勢科技創新團隊建設專項計劃項目（20171BCB24007）、江西省自然科學基金(20114BAB206006)


Effect of Tool Offset on Weld Formation and Tensile Strength of Friction Stir Welded Ti/Al Dissimilar Metal Joints
Author:
Affiliation:

Nanchang Hangkong University

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    采用攪拌摩擦焊(FSW)完成了3 mm厚TC4鈦合金和2A14-T14鋁合金的連接,研究了攪拌頭偏移對接頭的成形及拉伸性能的影響。結果表明在攪拌頭向鋁合金側的偏移對接頭的最大抗拉強度有顯著的影響。接頭最大抗拉強度隨攪拌頭的偏移量的增加逐漸升高。在偏移量為2.0 mm、攪拌頭轉速從400 r/min增加到700 r/min時,接頭的最大抗拉強度逐漸降低。在偏移量為2.5 mm、接頭的最大抗拉強度隨轉速的增加逐漸升高。當在攪拌頭轉速為700 r/min, 焊接速度為60 mm/min時,所得接頭強度最高,約347 MPa,為鋁合金母材的83 %。接頭的斷裂位置和拉伸強度均取決于微觀組織和金屬間化合物。對于強度最高的接頭,由于TiAl相的生成,接頭于鋁合金側熱影響區發生斷裂。

    Abstract:

    3mm thick TC4 titanium alloy and 2A14-T4 aluminum alloy were well joined by friction stir welding (FSW), and the influence of tool offset on weld formation and tensile property of the joints was investigated. The results show that tool offset to the Al side has significant influence on ultimate tensile strength (UTS) of the joints. With the increase of tool offset, the UTS increases gradually. When the tool offset is 2.0mm, the UTS of the joint decreases with increasing tool rotation speed from 400r/min to 700r/min. However, when the tool offset is increased to 2.5mm, the UTS of the joint increase with the increase of tool rotation speed. A tool rotation speed of 700r/min and a welding speed of 60mm/min is matched, the highest UST of 347MPa of the joint is obtained, which reaches to about 83% of Al matrix. The tensile results prove that the fracture location and tensile strength of the joints mainly depend on microstructure and intermetallic phases. For the joint with the highest strength, the fracture occurs in the heat affected zone (HAZ) of Al matrix due to brittle TiAl phase formed in the joint.

    參考文獻
    相似文獻
    引證文獻
引用本文

陳玉華,曹文明,周興汶,李樹寒,戈軍委.攪拌頭偏移對Ti/Al異種金屬攪拌摩擦焊接頭成形及拉伸強度的影響[J].稀有金屬材料與工程,2019,48(1):63~70.[Chen Yuhua, Cao Wenming, zhouxingwen, Li Shuhan, Ge Junwei. Effect of Tool Offset on Weld Formation and Tensile Strength of Friction Stir Welded Ti/Al Dissimilar Metal Joints[J]. Rare Metal Materials and Engineering,2019,48(1):63~70.]
DOI：10.12442/j. issn.1002-185X.20170599

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2017-07-07
  • 最后修改日期:2017-11-22
  • 錄用日期:2018-01-09
  • 在線發布日期: 2019-02-18
  • 出版日期: