8(MnFe)2Si和α-Al8(MnFeCr)2Si相存在。采用水冷銅模鑄造的含Mn和Zr的6061鋁合金,其拉伸性能得到明顯改善。經均勻化處理后其抗拉強度達到286MPa、屈服強度127MPa,延伸率17.84%。"/>

最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
水冷銅模對添加Mn和Zr的6061鋁合金微觀組織及力學性能的影響
作者:
作者單位:

東北大學

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金資助(No.51301109)


Effects of Water-Cooling Cu Mould on Microstructure and Mechanical Properties of 6061 Aluminum Alloy with Mn and Zr Addition
Author:
Affiliation:

Northeastern University

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    研究了水冷銅模鑄造對添加Mn和Zr元素的6061鋁合金的微觀組織及力學性能的影響。利用金相顯微鏡、掃描電鏡和EDS能譜,分析合金的微觀組織；結合X射線衍射分析及Vegard定律,估算鑄態及均勻化處理后Mg,Si和Mn元素在合金中的固溶度；通過拉伸實驗測試含Mn和Zr 的6061鋁合金力學性能。結果表明：水冷銅模亞快速凝固鑄造降低了溶質元素Mg、Si、Mn在鑄態合金中的偏析,減少了合金的均勻化處理時間；Mn和Zr元素的添加,使晶粒細化明顯；水冷銅模使鑄態析出相由骨骼狀和條狀的β鐵相轉變?yōu)轭w粒狀的α鐵相,均勻化處理后主要以顆粒狀的α-Al8(MnFe)2Si和α-Al8(MnFeCr)2Si相存在。采用水冷銅模鑄造的含Mn和Zr的6061鋁合金,其拉伸性能得到明顯改善。經均勻化處理后其抗拉強度達到286MPa、屈服強度127MPa,延伸率17.84%。

    Abstract:

    Effects of sub-rapid solidification by water-cooling Cu mould on microstructure and mechanical properties of 6061 aluminum alloy with Mn and Zr addition were investigated. Microstructure of the alloys was analyzed by optical microscopy, scanning electron microscopy and EDS energy spectrum. Solubilities of Mg, Si and Mn elements in as-cast and homogenized Al alloys were estimated by X-ray diffraction and Vegard’s Law. Tensile tests were conducted to investigate the mechanical properties of 6061 aluminum alloy. Results showed that both the segregation of Mg, Si and Mn elements and homogenization time were decreased by sub-rapid solidification. The grain size had also been refined significantly by adding Mn and Zr elements. As-cast precipitated phase was transformed into α-Fe phase of granulate from β-Fe of bone and strip by water-cooling Cu mould., and they were maily granular α-Al8(MnFe)2Si和α-Al8(MnFeCr)2Si after homogenization treatment. Tensile properties of Al alloy with Mn and Zr addition casted by water-cooling Cu mould. The UTS, YS and Elongation of homogenized alloy researches to 286Mpa, 27Mpa and 17.84%, respectively.

    參考文獻
    相似文獻
    引證文獻
引用本文

申華,史建超,穆永亮,羅洪杰,姚廣春.水冷銅模對添加Mn和Zr的6061鋁合金微觀組織及力學性能的影響[J].稀有金屬材料與工程,2019,48(1):300~308.[Shen Hua, Shi Jianchao, Mu Yongliang, Luo Hongjie, Yao Guangchun. Effects of Water-Cooling Cu Mould on Microstructure and Mechanical Properties of 6061 Aluminum Alloy with Mn and Zr Addition[J]. Rare Metal Materials and Engineering,2019,48(1):300~308.]
DOI：10.12442/j. issn.1002-185X.20170429

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2017-05-24
  • 最后修改日期:2017-10-13
  • 錄用日期:2017-11-09
  • 在線發布日期: 2019-02-18
  • 出版日期: