2和Ni3Ti減少,趨于形成NiTi單相。當燒結溫度為1100℃時,試樣孔隙分布均勻,隨著燒結保溫時間的延長,燒結試樣孔隙度高達32.2%,孔徑范圍在100μm左右,符合人體骨組織植入物的要求。"/>

最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
工藝參數對Micro-FAST制備多孔NiTi合金的影響
DOI:
作者:
作者單位:

四川大學制造科學與工程學院,四川大學制造科學與工程學院,四川大學制造科學與工程學院,四川大學制造科學與工程學院,四川大學制造科學與工程學院

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金資助(51605317)；國家自然科學基金資助(51575369)國家自然科學基金資助(51675357)


Effects of Technological Parameters on the Porous NiTi Alloys Prepared by Micro-FAST
Author:
Affiliation:

School of Manufacturing Science and Engineering,Sichuan University,Chengdu,School of Manufacturing Science and Engineering,Sichuan University,Chengdu,School of Manufacturing Science and Engineering,Sichuan University,Chengdu,School of Manufacturing Science and Engineering,Sichuan University,Chengdu,School of Manufacturing Science and Engineering,Sichuan University,Chengdu

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    多孔NiTi合金由于其良好的生物相容性以及獨特的力學性能在生物醫用領域具有廣闊的應用前景。本文采用Micro-FAST技術成功制備出多孔NiTi合金,燒結時間短,成本低,節能環保。研究結果表明,隨著燒結溫度的升高,試樣的孔隙度先減小后增加,再略微減小,有害相NiTi2和Ni3Ti減少,趨于形成NiTi單相。當燒結溫度為1100℃時,試樣孔隙分布均勻,隨著燒結保溫時間的延長,燒結試樣孔隙度高達32.2%,孔徑范圍在100μm左右,符合人體骨組織植入物的要求。

    Abstract:

    Porous NiTi alloys have broad potential application in the biomedical field due to their good biocompatibility and unique mechanical properties. Porous NiTi alloys were successfully prepared by using Micro-FAST which can realize the sintering process in a short sintering time at a low cost and in a environmental-friendly way. It was found that with the increasing sintering temperature, the porosity of the porous NiTi alloys decreased firstly, then increased and slightly reduced finally. Undesired NiTi2 and Ni3Ti phases were formed and decreased gradually with a trend to form single NiTi phase. At the sintering temperature of 1100℃, the porous NiTi alloys exhibited well-distributed pores. With the increasing holding time, the porosity increased significantly to 32.2% and the pore sizes were about 100μm, which meets the requirement of human bone implants.

    參考文獻
    相似文獻
    引證文獻
引用本文

高翌,趙旦,劉劍,楊屹,楊剛.工藝參數對Micro-FAST制備多孔NiTi合金的影響[J].稀有金屬材料與工程,2017,46(8):2190~2196.[Yi Gao, Dan Zhao, Jian Liu, Yi Yang, Gang Yang. Effects of Technological Parameters on the Porous NiTi Alloys Prepared by Micro-FAST[J]. Rare Metal Materials and Engineering,2017,46(8):2190~2196.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2016-11-22
  • 最后修改日期:2017-01-20
  • 錄用日期:2017-02-20
  • 在線發布日期: 2017-11-16
  • 出版日期: