最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
光斑直徑對純鈦薄片激光封孔的影響
DOI:
作者:
作者單位:

南昌航空大學 輕合金加工科學與技術國防重點學科實驗室,南昌航空大學 輕合金加工科學與技術國防重點學科實驗室,南昌航空大學 輕合金加工科學與技術國防重點學科實驗室,南昌航空大學 輕合金加工科學與技術國防重點學科實驗室,哈爾濱工業大學 先進焊接與連接國家重點實驗室

作者簡介:

通訊作者:

中圖分類號:

TG456.7

基金項目:

國家自然科學基金資助(51365044)；南昌航空大學研究生創新基金(YC2015025).


Effect of Spot Size on Joint Formation of Laser Hole Sealing of CP-Ti Sheet
Author:
Affiliation:

National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology,Nanchang Hangkong University,National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology,Nanchang Hangkong University,National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology,Nanchang Hangkong University,National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology,Nanchang Hangkong University,State Key Laboratory of Advanced Welding and Joining,Harbin Institute of Technology

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    采用Nd：YAG低功率脈沖激光對0.4mm純鈦薄片的微孔進行封焊，研究光斑直徑對焊縫成形的影響規律，并分析作用于封接區的激光能量變化。研究表明，當光斑直徑不大于0.4mm時小孔能夠完全封接，封接區有效厚度隨著光斑直徑的增大呈先增大后減小的趨勢，其最大有效封接厚度約為352μm，封接接頭主要由不同形態的α晶粒組成，在封接區邊緣存在較大的熱影響區。另外，隨著光斑直徑的增大，封接區上表面熔化面積基本不變，但封接模式由匙孔型向熱導型轉變，其中熱導型模式更適合小孔封接。對作用于封接區的激光能量計算發現，理論能量值與光斑直徑成正相關，而實際金屬熔化量與光斑直徑成反相關，造成此現象的原因是小孔邊緣熔化的金屬在重力等力的作用下向小孔內流動，從而可以吸收更多的激光能量。

    Abstract:

    Laser seal welding of 0.4mm thickness pure titanium with holes was achieved by N d: YAG pulse laser. The effect of laser spot size on the weld geometry of the sealed joint was studied. The results show that full seal welded joint can be achieved when the spot diameter is no more than 0.4mm. The effective thickness of sealing area increases at first then decreases with the increasing of spot diameter. The maximum effective sealing thickness is about 352μm.The sealing joint was consisted of alpha grains with different shapes, and there was a large HAZ in the joint. Besides, with the increase of the spot diameter, the surface melting area of the sealed joint is basically unchanged, but the sealing mode is changed from the keyhole to the heat-conduction type, and the heat-conduction model is more suitable for the hole sealing. Further, calculated laser energy of sealing area shown that there was a positive proportion between the theoretical energy value and laser spot size, but the theoretical analysis does not match with the actual situation. The reason may be that the molten metal beside the hole flow into the hole under the effect of gravity and other forces, which cause the increasing of actual absorption of laser energy.

    參考文獻
    相似文獻
    引證文獻
引用本文

黃永德,毛錦榮,周興汶,陳玉華,何鵬.光斑直徑對純鈦薄片激光封孔的影響[J].稀有金屬材料與工程,2018,47(8):2429~2424.[Huang Yongde, Mao Jinrong, Zhou Xinwen, Chen Yuhua, He Peng. Effect of Spot Size on Joint Formation of Laser Hole Sealing of CP-Ti Sheet[J]. Rare Metal Materials and Engineering,2018,47(8):2429~2424.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2016-08-03
  • 最后修改日期:2016-09-28
  • 錄用日期:2016-11-10
  • 在線發布日期: 2018-10-17
  • 出版日期: