2Al和Ti3Al中,析出相主要由TiAl、Ti2Al(Fe)、Ti3Al(Fe)和富Ti相組成；該比例的混合粉末在熱壓燒結過程中發生了不同程度的擴散反應,最終形成了組織漸變的Ti/Ti3Al(Fe)//Ti2Al(Fe)/TiAl顯微結構。"/>

最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
熱壓燒結制備鈦基合金(TiAl+Ti)及其顯微結構
DOI:
作者:
作者單位:

北京航空材料研究院 焊接與塑性成形研究所,北京航空材料研究院 焊接與塑性成形研究所,北京航空材料研究院 焊接與塑性成形研究所,沈陽飛機工業集團有限公司,北京航空材料研究院 焊接與塑性成形研究所,北京航空材料研究院 焊接與塑性成形研究所

作者簡介:

通訊作者:

中圖分類號:

基金項目:

航空科學基金(2014ZF21010)


Preparation and Microstructure Characterization of Ti-based Alloy (TiAl + Ti)by Hot-pressed Sintering
Author:
Affiliation:

Laboratory of Welding and Forging,Beijing Institute of Aeronautical Materials,Laboratory of Welding and Forging,Beijing Institute of Aeronautical Materials,Laboratory of Welding and Forging,Beijing Institute of Aeronautical Materials,Shenyang Aircraft Corporation,Laboratory of Welding and Forging,Beijing Institute of Aeronautical Materials,Laboratory of Welding and Forging,Beijing Institute of Aeronautical Materials

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    在1473K,30MPa,1.5h的熱壓條件下直接燒結TiAl金屬間化合物和Ti混合粉末,制備了鈦基合金(TiAl+Ti)樣品,采用XRD、SEM研究了兩種不同成分配比對燒結產物相組成及顯微結構的影響。結果表明,不同成分配比熱壓燒結體的顯微組織分布相差較大,但相組成基本相同；對于TiAl和Ti體積比7:3的鈦基合金樣品,Ti粉末中Fe元素易于固溶到Ti2Al和Ti3Al中,析出相主要由TiAl、Ti2Al(Fe)、Ti3Al(Fe)和富Ti相組成；該比例的混合粉末在熱壓燒結過程中發生了不同程度的擴散反應,最終形成了組織漸變的Ti/Ti3Al(Fe)//Ti2Al(Fe)/TiAl顯微結構。

    Abstract:

    Fabrication of TiAl strengthened Ti-based alloy by hot-pressed sintering of mixed powders of TiAl and Ti was studied at 1473 K under a pressure of 30 MPa for 1.5 h. The effects of composition ratio on the phase constitute and microstructures of hot-pressed sintering products were subsequently analyzed by XRD and SEM. Large difference exists in the phase distribution for the sintering products with different composition rations occurred. The feasibility of TiAl reinforced Ti-based alloy was confirmed with TiAl/Ti volume ratio of 7:3. Element Fe was examined to be concentrated in Ti2Al and Ti3Al. TiAl, Ti2Al(Fe), Ti3Al(Fe) and Ti-based phases were mainly formed in the sintering product. Different types of diffusion reactions occurred within the sintered body during hot-pressed sintering, finally leading to the formation of fine graded microstructures, Ti/Ti3Al(Fe)//Ti2Al(Fe)/TiAl.

    參考文獻
    相似文獻
    引證文獻
引用本文

于秋穎,方爽,熊華平,肇恒躍,張敏聰,王淑云.熱壓燒結制備鈦基合金(TiAl+Ti)及其顯微結構[J].稀有金屬材料與工程,2017,46(5):1370~1374.[YU Qiu-ying, FANG Shuang, XIONG Hua-ping, ZHAO Heng-yue, ZHANG Min-cong, WANG Shu-yun. Preparation and Microstructure Characterization of Ti-based Alloy (TiAl + Ti)by Hot-pressed Sintering[J]. Rare Metal Materials and Engineering,2017,46(5):1370~1374.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2016-05-12
  • 最后修改日期:2016-07-05
  • 錄用日期:2016-08-18
  • 在線發布日期: 2017-09-27
  • 出版日期: