s達到1.53T,最大磁導率μmax達到2630。"/>

最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
直接噴墨打印成形鐵磁軟磁材料的工藝研究
DOI:
作者:
作者單位:

北京科技大學新材料技術研究院,北京科技大學新材料技術研究院,北京科技大學新材料技術研究院,北京科技大學新材料技術研究院

作者簡介:

通訊作者:

中圖分類號:

TB31

基金項目:

國家自然科學基金資助(項目號51274039)


Preparation of Ferromagnetic Soft Magnetic Material by Direct Inkjet Printing Process
Author:
Affiliation:

Institute for Advanced Material Technology,University of Science and Technology Beijing,Institute for Advanced Material Technology,University of Science and Technology Beijing,Institute for Advanced Material Technology,University of Science and Technology Beijing,Institute for Advanced Material Technology,University of Science and Technology Beijing

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    本文以羰基鐵粉為原料,用DISPER-Y220為分散劑,制備出粘度為0.55Pa.s,流動性良好的料漿,以此料漿作為打印“墨水”,利用直接噴墨打印成形技術制備純鐵軟磁材料制件。噴頭直徑分別以0.5mm、0.8mm和1.0mm打印零件,打印成形后通過脫脂和燒結制備出制件。結果表明：分散添加量為1wt%時,料漿粘度最低,隨著固含量的增大,料漿粘度變大,隨著剪切速率的增大,料漿表現為剪切變稀特征；噴頭直徑為0.8mm所打印的燒結體,表面粗糙度最低,其Ra為0.8μm；在1300℃保溫2h燒結后,噴頭直徑為0.5mm的燒結體致密度最高,為96.3%,其磁飽和感應強度Bs達到1.53T,最大磁導率μmax達到2630。

    Abstract:

    In this paper, carbonyl iron powder and DISPER-Y220 are used as raw material and dispersant, respectively. The viscosity of slurry is detected as 0.55 Pa ? s and the slurry has good flowability slurry to be a printing ink. The ferromagnetic soft magnetic workpieces are prepared by direct inkjet printing process with the nozzle size of 0.5mm, 0.8mm and 1.0mm respectively, and then the samples printed have been through degreasing and sintering. The results showed that the viscosity of the slurry is lowest when the dosage of dispersant is1wt% and the viscosity of the slurry is increased with the solids content and shear rate increased .The slurry is shear thinning over the shear rate .The sintered body printed with the nozzle size of 0.8mm has a lowest surface roughness of 0.8μm. After sintered at 1300 ℃ for 2h ,the sintered body printed with the nozzle size of 0.5mm has a relative density of 96.3%, the saturation magnetization (BS ) and the maximum magnetic permeability (μmax ) reaching to 1.53T and 2630, respectively.

    參考文獻
    相似文獻
    引證文獻
引用本文

任向遠,邵慧萍,鄭航,張樂.直接噴墨打印成形鐵磁軟磁材料的工藝研究[J].稀有金屬材料與工程,2018,47(2):606~611.[Ren Xiangyuan, Shao Huiping, Zheng Hang, Zhang Le. Preparation of Ferromagnetic Soft Magnetic Material by Direct Inkjet Printing Process[J]. Rare Metal Materials and Engineering,2018,47(2):606~611.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2015-12-18
  • 最后修改日期:2016-04-22
  • 錄用日期:2016-05-18
  • 在線發布日期: 2018-03-15
  • 出版日期: