最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
硼對醫用Ti-22Nb-6Zr記憶合金的顯微組織及性能的影響
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

廣東省科技計劃項目 (2012B010200020)


Effect of Boron Addition on the Microstructure and Properties of Ti-22Nb-6Zr Shape Memory Alloys
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    研究在Ti-22Nb-6Zr (at%) 合金中添加不同含量 (質量分?jǐn)?shù)) (0.02%~1.5%)的硼元素，通過粉末燒結法成功制備了性能優良的含硼Ti-22Nb-6Zr記憶合金。結合OM、XRD、SEM分析發現，隨著硼元素含量的增加，合金的β相基體中逐漸析出α相和TiB相，晶粒得到明顯細化。通過壓縮力學性能測試，發現硼元素對Ti-22Nb-6Zr合金的彈性模量和超彈性影響不大，但硼含量對其屈服強度和抗壓強度有顯著影響，當硼含量為0.02 %~0.1%和1%時，合金展現出較高的抗壓強度（1450 MPa以上）和屈服強度（1250 MPa以上）。通過電化學測試，發現當硼含量在0.02%~1%時，合金具有較好的耐腐蝕性，腐蝕電流密度保持在10-6 A·cm-2以內。綜合考慮合金的顯微組織、力學性能與抗腐蝕性能，得出Ti-22Nb-6Zr記憶合金中適宜的硼添加量為0.02%~0.1%和1%

    Abstract:

    Ti-22Nb-6Zr (at%) shape memory alloys with various amount of boron (B) addition (0.02 wt%~1.5 wt%) were fabricated using a powder sintering method. Optical microscope, XRD and SEM were used to investigate the microstructure and phase constituents of the sintered alloys. It is shown that boron addition induces the precipitation of α phase and TiB phase in β matrix, which facilitates distinct refinement of microstructure. The addition of boron exerts only little influence on the Young’s modulus (around 30 GPa) and superelasticity (over 3%), but affects strongly the compression strength and yield strength of sintered Ti-22Nb-6Zr-B alloys. In order to acquire a relatively high yield strength and compression strength, the amount of boron addition into Ti-22Nb-6Zr shape memory alloys should be around 0.02 wt%~0.1 wt% and 1 wt%. Polarization curves analysis shows that the corrosion resistance of these Ti-22Nb-6Zr-B alloys is very good when boron content is about 0.02 wt%~1 wt%. Taking into account microstructure, mechanical properties and corrosion resistance, the appropriate amount of B addition for Ti-22Nb-6Zr shape memory alloys is 0.02 wt%~0.1 wt% and 1 wt%

    參考文獻
    相似文獻
    引證文獻
引用本文

徐 偉,賴 銘,于 博,李松建,高 巖.硼對醫用Ti-22Nb-6Zr記憶合金的顯微組織及性能的影響[J].稀有金屬材料與工程,2015,44(12):3208~3214.[Xu Wei, Lai Ming, Yu Bo, Li Songjian, Gao Yan. Effect of Boron Addition on the Microstructure and Properties of Ti-22Nb-6Zr Shape Memory Alloys[J]. Rare Metal Materials and Engineering,2015,44(12):3208~3214.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2014-12-15
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期: 2016-08-29
  • 出版日期: 2015-12-25