最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
醫用多孔Ti-10Mo合金的制備及力學性能
DOI:
作者:
作者單位:

北京科技大學新材料技術研究院,北京科技大學新材料技術研究院,北京科技大學新材料技術研究院,北京科技大學新材料技術研究院,北京科技大學新材料技術研究院

作者簡介:

通訊作者:

中圖分類號:

TG146.2

基金項目:

國家自然科學基金資助(項目號51204015)；新金屬材料國家重點實驗室開放基金資助(項目號2012Z-10)


The preparation and mechanical properties of porous Ti - 10 Mo alloy for biomedical applications
Author:
Affiliation:

State Key Laboratory for Advanced Metals and Materials,University of Science and Technology Beijing,State Key Laboratory for Advanced Metals and Materials,University of Science and Technology Beijing,State Key Laboratory for Advanced Metals and Materials,University of Science and Technology Beijing,State Key Laboratory for Advanced Metals and Materials,University of Science and Technology Beijing,State Key Laboratory for Advanced Metals and Materials,University of Science and Technology Beijing

Fund Project:

National Natural Science Foundation of China (50674076, 50902115); Natural Science Foundation of Shaanxi Province (2013JZ015)

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    以元素粉末為原料添加造孔劑碳酸氫銨,采用粉末冶金模壓燒結技術制備了多孔Ti-10Mo合金,探討了燒結工藝與造孔劑含量對合金組織、孔隙特征和力學性能的影響規律。結果表明,在1300℃燒結可制備出具有典型魏氏體組織、孔隙分布均勻的多孔Ti-10Mo合金材料；隨著造孔劑含量增加,合金孔隙率增加,孔徑變大孔壁變薄,當造孔劑含量達到50%,孔隙結構互相貫通,孔徑尺寸大幅增加；添加50~60%造孔劑,制備Ti-10Mo合金孔隙率為62.8%~66.9%,平均孔徑尺寸為485~545μm,其彈性模量為2.9~1.3GPa,抗壓屈服強度為129.2~56.1GPa。

    Abstract:

    The porous Ti-10Mo alloys from elemental powders were fabricated by powder metallurgy technique with ammonium bicarbonate as the space-holder. The effects of sintering process and space-holder content on the microstructure, porous characteristics and mechanical properties were studied. The results show that at sintering temperature of 1300℃ the porous Ti-Mo alloys with uniform microstructure and pore distribution can be produced, and the alloy exhibit a typical Widmanstatten structure. With the increase of the space-holder content, the pores become larger and the hole wall gets thinner. At or above 50wt% of space-holder, pores are interconnected, leading to forming a three-dimensional connectivity structure. When the space-holder content is in the range of 50%~60% , the alloys obtained show porosity of 62.8%~66.9%, and their elastic modulus and compressive yield strength vary from 2.9 to 1.3 GPa, and from 129.2 to 56.1 MPa, respectively.

    參考文獻
    相似文獻
    引證文獻
引用本文

支玲玲,路新,孟慶宇,徐偉,曲選輝.醫用多孔Ti-10Mo合金的制備及力學性能[J].稀有金屬材料與工程,2016,45(6):1554~1558.[Zhi Lingling, Lu Xin, Meng Qingyu, XU Wei, Qu Xuanhui. The preparation and mechanical properties of porous Ti - 10 Mo alloy for biomedical applications[J]. Rare Metal Materials and Engineering,2016,45(6):1554~1558.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2015-06-03
  • 最后修改日期:2015-08-26
  • 錄用日期:2015-10-13
  • 在線發布日期: 2016-10-08
  • 出版日期: