最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
固溶時效工藝對7055鋁合金組織和力學性能的影響
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家國際科技合作專項項目 (2011DFR50950)；國家科技支撐計劃課題 (2012BAF09B04)；重慶大學大型儀器設備開放基金


Effects of Solution and Aging Treatments on the Microstructures and Mechanical Properties of 7055 Al Alloys
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    采用透射電子顯微鏡、光學顯微鏡、拉伸力學性能測試等手段比較分析了不同固溶時效工藝對7055鋁合金擠壓棒材微觀組織結構和力學性能的影響規律和機理。結果表明，固溶和時效工藝的合理搭配對控制合金微細結構、獲得理想的綜合力學性能有重要作用。采用470 ℃/20 min+480~490 ℃/20 min的兩級固溶處理可以進一步減少合金中未溶化合物的數量，有利于增加時效強化效果；當?shù)诙?jí)固溶溫度為490 ℃時，可以使未溶化合物數量明顯減小，其體積分?jǐn)?shù)從單級固溶的2.5%降低至約2.0%；晶粒尺寸在30~35 μm。本試驗條件下，7055鋁合金擠壓棒材經 470 ℃/20 min+485 ℃/20 min 兩級固溶處理和隨后的135 ℃/16 h + 190 ℃/10 min兩級時效處理，抗拉強度和屈服強度分別達到694和660 MPa，延伸率仍保持14%，合金具有最佳的綜合力學性能

    Abstract:

    The effects of solution and aging treatments on the microstructures and mechanical properties of 7055 Al alloy bars were studied by transmission electron microscopy, optical microscopy and tensile mechanical property testing. The results show that an appropriate combination of solution and aging treatments plays an important role in controlling microstructure so as to obtain improved mechanical properties. Two-step solution of 470 oC/20 min+480~490 oC/20 min could further decrease the amount of undissolved particles and is helpful to enhance age-strengthening. When the 2nd-step solution temperature is increased to 490 oC, the volume fraction of undissolved particles decreases remarkably, from 2.5% in the case of one-step solution treatment to 2.0%. The grain size of the as-solutioned alloys under experimental conditions is in the range of 30~35 μm. Optimum combined mechanical properties are achieved under the regime of 470 oC/20 min+485 oC/20 min solution- treatment followed by 135 oC/16 h + 190 oC/10 min aging treatment, with the tensile strength and yield strength being 694 MPa and 660 MPa, respectively, in the meantime maintaining a high elongation to failure of 14%

    參考文獻
    相似文獻
    引證文獻
引用本文

張 靜,楊 亮,左汝林.固溶時效工藝對7055鋁合金組織和力學性能的影響[J].稀有金屬材料與工程,2015,44(4):956~960.[Zhang Jing, Yang Liang, Zuo Rulin. Effects of Solution and Aging Treatments on the Microstructures and Mechanical Properties of 7055 Al Alloys[J]. Rare Metal Materials and Engineering,2015,44(4):956~960.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2014-04-29
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期: 2015-06-08
  • 出版日期: