最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
反復鐓壓6013型鋁合金的組織和性能
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

江蘇省工業科技支撐項目 (BE2008118)；江蘇省普通高校研究生科研創新計劃 (CXLX12_0620)；南通市科技應用研究計劃項目 (BK2011010)


Microstructure and Properties of 6013 Type Aluminum Alloy Produced by Cyclic Channel Die Compression Process
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    以6013型鋁合金為試驗對象，研究了反復鐓壓工藝制備細晶材料，消除合金各向異性的可行性。采用金相顯微鏡，透射電鏡研究了6013型鋁合金反復鐓壓對合金組織和性能的影響。結果表明：反復鐓壓使合金內部產生取向各異、彼此交錯的變形帶，有利于細化合金組織，經480 ℃, 2 h的退火處理后，合金發生再結晶，合金晶粒等軸化，大小分布均勻，與未反復鐓壓合金組織相比，晶粒顯著細化，減輕了組織各向異性；合金強度隨鐓壓道次的增加，先降低后升高，對鐓壓后的合金進行T6處理（560 ℃, 2 h+191 ℃, 4 h），反復鐓壓3道次和12道次合金的硬度分別為1418.5和1503.5 MPa。研究表明：反復鐓壓工藝可以有效細化晶粒，消除組織各向異性，多道次鐓壓后，合金強度有所提高

    Abstract:

    6013 type aluminum alloy produced by cyclic channel die compression (CCDC) process was investigated to explore whether the fine grain and elimination of anisotropy can be obtained. Microstructures and properties of 6013 type aluminum alloy were tested by optical microscopy (OM), transmission electron microscopy (TEM) and hardness tester. The results indicate that CCDC process can effectively refine the grains and eliminate the anisotropy. Different-orientation, staggered belts are observed, which is conducive to refining the microstructure when the alloy is subjected to CCDC process. Recrystallization, equiaxed grains, and homogeneous distribution are gotten when the alloy is annealed at 480 oC for 2 h. The grains are significantly refined and the microstructural anisotropy is reduced compared with the alloy without CCDC. The strength of the alloy decreases first and then increases with increasing the passes of CCDC. The hardness (HV) of the alloy is 1418.5 MPa and 1503.5 MPa compressed by 3 passes and 12 passes, respectively, when the alloy was treated by T6 solution-aging (560 oC /2 h+191 oC /4 h). It is shown that the fine grain and elimination of anisotropy can be obtained and the strength would be increased after multi-passes CCDC

    參考文獻
    相似文獻
    引證文獻
引用本文

張福豹,許曉靜,張?jiān)士?張振強,吳 瑤.反復鐓壓6013型鋁合金的組織和性能[J].稀有金屬材料與工程,2014,43(11):2819~2823.[Zhang Fubao, Xu Xiaojing, Zhang Yunkang, Zhang Zhenqiang, Wu Yao. Microstructure and Properties of 6013 Type Aluminum Alloy Produced by Cyclic Channel Die Compression Process[J]. Rare Metal Materials and Engineering,2014,43(11):2819~2823.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2013-11-25
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期: 2015-04-07
  • 出版日期: