最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
擠壓態Mg-Sm-Ca合金的顯微組織和力學性能
DOI:
作者:
作者單位:

太原科技大學,太原科技大學,太原科技大學,太原科技大學

作者簡介:

通訊作者:

中圖分類號:

TG146.2

基金項目:

太原科技大學博士科研啟動項目（20122011）


Microstructure and mechanical properties of extruded Mg-Sm-Ca alloys
Author:
Affiliation:

Taiyuan University of Science and Technology,Taiyuan University of Science and Technology,Taiyuan University of Science and Technology,Taiyuan University of Science and Technology

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    研究了擠壓Mg-4.0Sm-xCa (x=0.5, 1.0 and 1.5 wt%)合金經過200 oC等溫時效處理后的顯微組織、時效硬化行為和力學性能。結果表明，隨著Ca的添加，在鎂基體中形成針/棒狀的Mg2Ca相、塊狀和顆粒狀含Ca元素的Mg41Sm5相，合金的晶粒被細化、拉伸力學性能得到顯著提高。在 T5（峰值時效）態下，Mg-4.0Sm-1.0Ca合金具有最細的晶粒尺寸，其大小約為 5.1 μm。隨著Ca含量的增加，針/棒狀的Mg2Ca相逐漸增多,當Ca含量達到1.5 wt%時，晶界處含Ca的塊狀Mg41Sm5相的量明顯減少。在峰值時效態下，Mg-4.0Sm-1.0Ca合金具有最大的硬度值（82 HV）以及最佳的力學性能，其抗拉強度、屈服強度和延伸率分別達到了267 MPa, 189 MPa 和 24%。合金力學性能的提高主要?dú)w因于晶粒細化、固溶強化以及Mg2Ca相和Mg41Sm5相的析出強化。

    Abstract:

    Microstructure, age hardening response and mechanical properties of Mg-4.0Sm-xCa (x=0.5, 1.0 and 1.5 wt%) alloys during extrusion and subsequent isothermal aging at 200 oC were investigated. The results indicate that with the addition of Ca, the bulk and particle-like Mg41Sm5 phases containing Ca and the needle/rod-like Mg2Ca phases form in the Mg matrix, grains of the alloy are refined and tensile mechanical properties are improved remarkably. In T5 (peak-aging) condition, the Mg-4.0Sm-1.0Ca alloy shows the smallest grain size of 5.1 μm. The amount of Mg2Ca phase increases gradually, but that of the bulk Ca-containing Mg41Sm5 phase in alloy with 1.5 wt% Ca significantly decrease, which mainly distribute at the grain boundaries. The peak-aged Mg-4.0Sm -1.0Ca alloy exhibits the highest peak hardness (82 HV) and the optimal ultimate tensile strength, yield tensile strength and elongation of 267 MPa, 189 MPa and 24%, respectively. The improved mechanical properties of the alloy are attributed to grain refinement, solution strengthening and precipitation strengthening of Mg2Ca phase and Mg41Sm5 phase.

    參考文獻
    相似文獻
    引證文獻
引用本文

柴躍生,高志剛,蔡康樂,房大慶.擠壓態Mg-Sm-Ca合金的顯微組織和力學性能[J].稀有金屬材料與工程,2016,45(2):287~291.[chaiyuesheng, gao zhi gang, cai kang le, fang da qing. Microstructure and mechanical properties of extruded Mg-Sm-Ca alloys[J]. Rare Metal Materials and Engineering,2016,45(2):287~291.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2014-01-22
  • 最后修改日期:2014-07-13
  • 錄用日期:2014-08-12
  • 在線發布日期: 2016-07-15
  • 出版日期: