最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
擠壓溫度對Mg-2.0Zn-0.3Zr-0.9Y新型鎂合金組織和性能的影響
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家重點基礎研究發展規劃（973計劃）（2007CB613700）；“十一五”國家支撐計劃（2007BAQ00134-04）；國家自然科學基金（50725413）


Effects of Extruding Temperature on Microstructure and Mechanical Properties of Mg-2.0Zn-0.3Zr-0.9Y Alloy
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    研究了不同擠壓溫度對Mg-2.0Zn-0.3Zr-0.9Y新型鎂合金組織和性能的影響。結果表明，降低擠壓溫度，Mg-2.0Zn-0.3Zr-0.9Y合金的平均晶粒尺寸得到顯著細化，合金的屈服強度和抗拉強度得到大幅提高，而延伸率變化不大。隨著擠壓溫度的降低，{102}織構強度不斷增強，{0002}基面環形織構強度減弱。Mg-2.0Zn-0.3Zr-0.9Y合金的力學性能不但受到組織平均晶粒大小的影響，還受到織構分布的影響。擠壓溫度為330 ℃時可獲得細小的組織和優良的力學性能，平均晶粒尺寸達到1.76 μm，合金抗拉強度達到323 MPa，屈服強度為309 MPa，延伸率為21.92%。

    Abstract:

    The effects of extruding temperatures on the microstructures and mechanical properties of the Mg-2.0Zn-0.3Zr-0.9Y magnesium alloy were investigated. The results show that the grain size of Mg-2.0Zn-0.3Zr-0.9Y alloy is significantly refined by decreasing the extruding temperature. Meanwhile the tensile strength and the yield strength are greatly enhanced, but the elongation is increased little. With the decrease of extruding temperature, the intensity of {102} texture is enhanced, while that of the {0002} basal ring type texture is decreased. The mechanical properties of the alloy are not only related with the average grain size, but also with the texture. Mg-2.0Zn-0.3Zr-0.9Y magnesium alloy extruded at 330 °C possesses a fine grain size of 1.76 μm on average and good mechanical properties including the elongation of 21.92%, the yield strength of 309 MPa and the tensile strength of 323 MPa.

    參考文獻
    相似文獻
    引證文獻
引用本文

呂濱江,彭 建,童小山,潘復生.擠壓溫度對Mg-2.0Zn-0.3Zr-0.9Y新型鎂合金組織和性能的影響[J].稀有金屬材料與工程,2013,42(4):841~844.[Lü Binjiang, Peng Jian, Tong Xiaoshan, Pan Fusheng. Effects of Extruding Temperature on Microstructure and Mechanical Properties of Mg-2.0Zn-0.3Zr-0.9Y Alloy[J]. Rare Metal Materials and Engineering,2013,42(4):841~844.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2012-04-21
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期:
  • 出版日期: