最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
焊后熱處理對鋁鋰合金電子束焊接頭組織與性能的影響
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

南昌航空大學輕合金加工科學與技術國防重點學科實驗室開放課題研究基金 (gf201001001)


Influence of Post-Weld Heat Treatment on Microstructure and Mechanical Properties of Al-Li Alloy Electron Beam Welding Joint
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    對2090鋁鋰合金電子束焊接頭進行焊后熱處理，熱處理工藝為530 ℃固溶0.5 h +190 ℃時效12 h。結果發現，焊接接頭的抗拉強度由焊態下的331 MPa提高到熱處理后的415 MPa，焊后熱處理使接頭的強度大大提高。金相組織觀察表明，鋁鋰合金電子束焊接頭經過熱處理后焊縫晶粒形貌由焊態下的等軸樹枝晶轉變成等軸晶，并且在晶粒內部和晶界處析出細小的強化相。XRD相結構分析顯示接頭焊縫中的強化相主要為δ′(Al3Li)、T1(Al2CuLi)、β′(Al3Zr)等。TEM觀察證實，熱處理后2090鋁鋰合金接頭焊縫中析出了多量的球狀δ′相和針狀T1相。拉伸斷口分析表明，鋁鋰合金電子束焊接頭在焊態下為帶韌窩的穿晶斷裂，經過熱處理后接頭斷裂模式轉變?yōu)檠鼐嗔选?/p>

    Abstract:

    2090 Al-Li alloy electron beam welding joints were heat treated after welding, and the heat treatment scheme was 530 °C quenching for 0.5 h + 190 °C artificial aging for 12 h. Results show that the strength of 2090 Al-Li alloy joint is from 331 MPa in the as-welded state to 415 MPa under the condition of post-weld heat treatment. Therefore, the post-weld heat treatment can increase the strength of Al-Li alloy joints greatly. The observation of joint microstructure demonstrates that the grain morphology of the weldment varies form equiaxed dendrites in as-welded state into equiaxed grains after heat treatment, and the fine strengthening phases precipitate within the grain and along the grain boundary. The XRD analysis of phase constituent indicates that the main strengthening phases in Al-Li weldment are δ′(Al3Li), T1(Al2CuLi) and β′(Al3Zr), etc. The TEM observation shows that after heat treatment, many strengthening phases of spheroidal δ′ and needle-like T1 precipitate in weld metal of 2090 Al-Li alloy joint, which contribute to the joint strength. The observation of joint tensile fracture shows that the Al-Li alloy electron beam welding joint presents the characteristic of transgranular ductile fracture in the as-welded state. After post-weld heat treatment, the Al-Li alloy welded joint presents the pattern of intergranular fracture

    參考文獻
    相似文獻
    引證文獻
引用本文

王少剛,俞 曠,陳 忱,邢 麗.焊后熱處理對鋁鋰合金電子束焊接頭組織與性能的影響[J].稀有金屬材料與工程,2013,42(3):579~584.[Wang Shaogang, Yu Kuang, Chen Chen, Xing Li. Influence of Post-Weld Heat Treatment on Microstructure and Mechanical Properties of Al-Li Alloy Electron Beam Welding Joint[J]. Rare Metal Materials and Engineering,2013,42(3):579~584.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2012-02-17
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期:
  • 出版日期: