最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
TiAl與Si3N4f/Si3N4復合材料釬焊接頭界面結構及性能研究
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金（50805038）


Research on the Interfacial Structure and Properties of TiAl - Si3N4f/Si3N4 Brazed Joints
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    采用AgCuTi釬料實現了TiAl與Si3N4f/Si3N4復合材料的釬焊，確定了釬焊接頭的典型界面組織結構為T(mén)iAl/AlCuTi /Ag(s,s)/TiN/ Si3N4f/Si3N4。釬焊過程中，液相釬料在Si3N4f/Si3N4復合材料表面發生較好潤濕，釬料中活性元素Ti與Si3N4基體及纖維發生反應形成連續的TiN化合物層。過高的釬焊溫度或過長的保溫時間導致釬縫中脆性的AlCuTi化合物增加，且由于接頭應力的作用在釬縫中產生微裂紋甚至開裂，嚴重地降低了釬焊接頭性能。當釬焊溫度T=850 ℃，保溫時間為10 min時，接頭抗剪強度達到最大，為9.4 MPa，超過Si3N4f/Si3N4母材層間抗剪強度的60%。斷口分析表明：壓剪過程中，斷裂發生在Si3N4f/Si3N4復合材料一側。

    Abstract:

    The TiAl alloy was brazed to Si3N4f/Si3N4 composite using AgCuTi filler metal. The typical interfacial microstructure of the joint is TiAl/AlCuTi reaction layer/Ag based solid solution/TiN reaction layer/Si3N4f/Si3N4. During the brazing process, liquid solder wets the surfaces of Si3N4f/Si3N4 composite well, and the active element Ti reacts with Si3N4 matrix and fibers to form continuous TiN compounds layer. The amount of brittle AlCuTi intermetallics increases when the brazing temperature is much higher or the brazing time is much longer. Some microcracks form in AlCuTi intermetallics due to the residual stress in the joint, which seriously degrade the joining properties. A maximum of 9.4 MPa of the shear strength can be obtained when the brazing temperature T=860 °C and holding time t=5 min, which exceeds 60% of the strength of composite materials. Fracture analysis shows that fracture occurs in the side of Si3N4f/Si3N4 composite.

    參考文獻
    相似文獻
    引證文獻
引用本文

宋曉國,曹 健,王義峰,馮吉才. TiAl與Si3N4f/Si3N4復合材料釬焊接頭界面結構及性能研究[J].稀有金屬材料與工程,2012,41(7):1247~1250.[Song Xiaoguo, Cao Jian, Wang Yifeng, Feng Jicai. Research on the Interfacial Structure and Properties of TiAl - Si3N4f/Si3N4 Brazed Joints[J]. Rare Metal Materials and Engineering,2012,41(7):1247~1250.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2011-07-23
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期:
  • 出版日期: