最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
成形壓力對Fe16Al2Cr多孔材料性能的影響
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

973-ITER計劃專項（2010GB113003）


Effect of Pressing Pressure on Performance of Fe16Al2Cr Porous Materials
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    以Fe16Al2Cr預合金粉末為原料，采用模壓成形、真空燒結的方法制備了Fe16Al2Cr多孔材料，研究了粉末成形壓力與Fe16Al2Cr多孔材料性能的關系。結果表明：小于31 μm的Fe16Al2Cr粉末的壓制成形性能較差，壓坯強度低；燒結過程中，厚度收縮遠大于徑向收縮，并隨著成形壓力的增大而減小；在較高的燒結溫度下，成形壓力和燒結時間對徑向收縮幾乎沒有影響；而孔隙度、最大孔徑和透氣度隨著成形壓力的增大而降低，并隨燒結時間延長而增大；增大成形壓力，延長燒結時間，有利于提高Fe16Al2Cr多孔材料的剪切強度。

    Abstract:

    Fe16Al2Cr porous material was prepared by compression molding, vacuum sintering using Fe16Al2Cr pre-alloy powder as raw material. The relationship between powder pressing pressure and Fe16Al2Cr porous material performance was researched. The results show that Fe16Al2Cr powder less than 31 μm of particles size is poor compaction performance and green body strength. In process of the power sintering, the axial contraction is bigger than radial contraction, and decreased with the pressing pressure increased. Pressing pressure and sintering time is almost no effects the radial shrinkage at higher sintering temperature. The porosity, pore size and permeability of Fe16Al2Cr porous material decrease with pressing pressure increases, and increases with the sintering time prolongation. Increasing pressing pressure and sintering time help to improve the shear strength of Fe16Al2Cr porous materials.

    參考文獻
    相似文獻
    引證文獻
引用本文

康新婷,湯慧萍,王建永,遲煜頔,楊保軍,王 建,李亞寧.成形壓力對Fe16Al2Cr多孔材料性能的影響[J].稀有金屬材料與工程,2011,40(10):1731~1736.[Kang Xinting, Tang Huiping, Wang Jianyong, Chi Yudi, Yang Baojun, Wang Jian, Li Yaning. Effect of Pressing Pressure on Performance of Fe16Al2Cr Porous Materials[J]. Rare Metal Materials and Engineering,2011,40(10):1731~1736.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2011-09-25
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期:
  • 出版日期: