最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
工藝參數和熱處理對純鈦表面激光熔覆原位合成羥基磷灰石涂層中物相組成的影響
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金(50971102)；國家重點基礎研究發展計劃(2007CB613805)；西北工業大學基礎研究基金(NPU-FFR-JC200808)；凝固技術國家重點實驗室(西北工業大學)自主研究課題（16-TZ-2007，39-QZ-2009）；高等學校學科創新引智計劃(08040)


Effects of Processing Parameters and Heat Treatment on Phase Structure of the Hydroxyapatite Coating on Pure Ti Surface by Laser Cladding in-situ Synthesis
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    使用CaCO3和CaHPO4混合粉末，在純鈦表面通過激光熔覆原位合成的方法制備羥基磷灰石(Ca10(PO4)6(OH)2，HA)涂層，研究了激光功率，掃描速度和熱處理對涂層物相的影響，以期提高涂層中HA的含量。結果表明，低功率下，涂層的主要組成物相為磷酸四鈣(Ca4(PO4)2O，TTCP)，同時有少量的HA，α-磷酸鈣(α-Ca3(PO4)2，α-TCP)，CaO和CaTiO3；隨功率的增加，涂層中的TTCP，HA和 CaO逐漸減少，只剩下α-TCP和CaTiO3。與功率相比，掃描速度對涂層物相的影響較小。當激光功率為400 W時，不同掃描速度下涂層的物相沒有發生明顯的變化，主要物相均為TTCP。將涂層在800 ℃下保溫5 h，然后隨爐冷卻，可以使涂層中的TTCP和α-TCP全部轉變?yōu)镠A，進而得到含HA較多的涂層。

    Abstract:

    Hydroxyapatite (Ca10(PO4)6(OH)2, HA) coatings were prepared on pure Ti substrates by laser cladding (LC) in situ synthesis using mixed powders of CaCO3 and CaHPO4. In order to increase the amount of HA in the coatings, the effects of processing parameters including laser power and scanning velocity and heat treatment on the phase structure of the coatings were investigated. The results show that the coatings consist of large amount of tetracalcium phosphate (Ca4(PO4)2O, TTCP) as well as a little HA, α-tricalcium phosphate (α-Ca3(PO4)2, α-TCP), calcium oxide(CaO) and CaTiO3 when the laser power is low. As the laser power increases, the amount of TTCP, HA and CaO in the coatings decreases gradually, and finally only α-TCP and CaTiO3 remain. Compared with the laser power, the effect of scanning velocity on the phase structure of the coatings is much weaker. At the laser power of 400 W, there is no obvious difference for the phase structures at different scanning velocities and the main phase is always TTCP. It is found that the amount of HA can be increased greatly by heat treatment at 800 oC for 5 h followed by furnace cooling, due to the total transformation from TTCP and α-TCP to HA.

    參考文獻
    相似文獻
    引證文獻
引用本文

呂曉衛,林 鑫,曹永青,胡 江,高 勃,黃衛東.工藝參數和熱處理對純鈦表面激光熔覆原位合成羥基磷灰石涂層中物相組成的影響[J].稀有金屬材料與工程,2011,40(4):714~717.[Lü Xiaowei, Lin Xin, Cao Yongqing, Hu Jiang, Gao Bo, Huang Weidong. Effects of Processing Parameters and Heat Treatment on Phase Structure of the Hydroxyapatite Coating on Pure Ti Surface by Laser Cladding in-situ Synthesis[J]. Rare Metal Materials and Engineering,2011,40(4):714~717.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2010-06-07
  • 最后修改日期:2010-12-27
  • 錄用日期:
  • 在線發布日期:
  • 出版日期: