最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
注射成形制備多孔鈦及其性能
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金（35770576）；國家“863”計劃資助項目（2007AA03Z114）


Fabrication of Bioactive Porous Titanium by Metal Injection Molding and Its Properties
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    以氯化鈉作為造孔劑，利用金屬注射成形(MIM)工藝制備多孔鈦。研究燒結溫度、造孔劑粒度和含量對多孔鈦孔隙度、微觀形貌和力學性能的影響。結果表明，隨著燒結溫度的升高，多孔鈦的孔隙度逐漸下降而抗壓強度和彈性模量逐漸升高；隨著造孔劑粒度的減小，多孔鈦的孔徑也隨之減??；隨著造孔劑含量的增多，多孔鈦的孔隙度逐漸增大；MIM多孔鈦植入體的最佳燒結溫度為1100~1200 ℃，NaCl的最優粒度為150~250 μm。

    Abstract:

    Metal injection molding (MIM) was used to fabricate porous titanium with sodium chloride (NaCl) as spacer-holder. The effects of sintering temperature, particle size and amount of the spacer-holder on porosity, microstructure and mechanical properties were investigated. The results show that the porosity of porous titanium decreases while the compressive strength and elastic modulus increases with the increasing of sintering temperature. The pore size of porous titanium decreases with the granularity of NaCl decreasing, and the porosity increases with the addition of spacer-holder. The optimum sintering temperature of MIM porous titanium implant is 1100-1200 oC, and the optimum granularity of NaCl is 150-250 μm.

    參考文獻
    相似文獻
    引證文獻
引用本文

李 挺,李益民,陳良建,何 浩,胡幼華.注射成形制備多孔鈦及其性能[J].稀有金屬材料與工程,2011,40(2):335~338.[Li Ting, Li Yimin, Chen Liangjian, He Hao, Hu Youhua. Fabrication of Bioactive Porous Titanium by Metal Injection Molding and Its Properties[J]. Rare Metal Materials and Engineering,2011,40(2):335~338.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2010-03-06
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期:
  • 出版日期: