最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

+高級檢索
TA15合金葉輪底漏式真空吸鑄成形工藝研究
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金項目（面上項目）國家自然科學基金項目(NSFC50975060);973項目（2011CB605504）；黑龍江省科技攻關項目（GZ09A206）


Research on Forming Process of TA15 Alloy Impeller under Bottom Pouring Vacuum Casting
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    研究了底漏式真空吸鑄成形方法制備鈦合金小型葉輪鑄件的可能性。首先研究了底漏式真空吸鑄工藝參數對TA15合金在水平方向的螺旋形型腔內流動性的影響，然后研究了工藝參數對1mm厚薄板鑄件在重力方向上充填率的影響，最后采用合理工藝參數成功吸鑄出鈦合金葉輪，葉輪鑄件輪廓完整，棱角清晰。結果表明，氣體壓力對充型能力有決定性影響，合金液不僅在重力方向具有很強的充型能力，而且在水平方向也能夠很好地充填型腔。

    Abstract:

    The possibility of minitype titanium alloy impeller cast preparation by bottom vacuum suction casting was studied. At first, the effects of the processing parameters of bottom pouring vacuum suction casting on the horizontal flowability of TA15 alloy in a spiral mold cavity were investigated; then their effects on the filling ratio in gravity direction of a 1 mm thick plate was researched; finally a TA15 impeller was produced by employing reasonable processing parameters. The impeller cast has an integrated structure and fine edges and corners. Results show that gas pressure has a predominant effect on the filling process. The melt has a good filling ability both in vertical and horizontal direction.

    參考文獻
    相似文獻
    引證文獻
引用本文

蘇彥慶. TA15合金葉輪底漏式真空吸鑄成形工藝研究[J].稀有金屬材料與工程,2012,41(1):902~905.[suyanqing. Research on Forming Process of TA15 Alloy Impeller under Bottom Pouring Vacuum Casting[J]. Rare Metal Materials and Engineering,2012,41(1):902~905.]
DOI：[doi]

復制
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2010-05-19
  • 最后修改日期:2010-09-08
  • 錄用日期:
  • 在線發布日期: 2012-01-06
  • 出版日期: