最新色国产精品精品视频,中文字幕日韩一区二区不卡,亚洲有码转帖,夜夜躁日日躁狠狠久久av,中国凸偷窥xxxx自由视频

TA15鈦合金擠壓薄壁型材拉伸性能及差異性研究
DOI:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

航材院鈦合金型材應用研究項目(KZ82171509)


Difference Research on Tensile Properties of TA15 Titanium Alloy Thin Profile Prepared by Hot Extrusion
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    針對"直接熱擠壓"和"熱擠壓+脈沖鍛打"TA15鈦合金薄壁型材的室溫力學性能及差異開展實驗研究。通過對型材不同位置切取的試樣進行拉伸試驗,獲得了型材抗拉強度和屈服強度分布規律,并對性能數據分布的均勻性和一致性進行深入分析。結果表明,"直接熱擠壓"態型材的抗拉強度和屈服強度數值分布較分散,強度離散系數大于3.5%;而"熱擠壓+脈沖鍛打"態型材的抗拉強度和屈服強度數值分布相對集中,不同批次型材之間的力學性能一致性較好,強度離散系數均小于3%。進一步分析表明,2種狀態型材之間的性能差異與型材表面狀態、表面細晶層和截面尺寸有關。脈沖鍛打能夠改善型材表面細晶層分布的均勻性和截面尺寸精度,從而改善型材力學性能分布的均勻性和一致性。

    Abstract:

    The room temperature mechanical properties of TA15 titanium alloy thin profiles which prepared by "direct hot extrusion"(DE) and "hot extrusion + pulse forging"(EF) process were studied by tensile test. The distribution regulation of tensile strength and yield strength were obtained by using the samples cut from different locations of profile. Then,the regulation of data distribution was analyzed. The results show that the values of tensile strength and yield strength distribute more scattered and the dispersion coefficient is larger than 3. 5% for DE profiles; By contrast,their distribution are more homogeneous and concentrated for EF profiles. Among different production lots,its distribution of test data is consistent and the dispersion coefficient is lower than 3%. By further analysis,the performance difference between two type profiles is related to surface states,fine grain layer and section size. Pulse forging process can uniform the thickness of fine grain layer and regulate section size,which are benefit for improving mechanical performance of the profile.

    參考文獻
    相似文獻
    引證文獻
引用本文

張明杰;齊立春;黃利軍;李雪飛;李煥峰;. TA15鈦合金擠壓薄壁型材拉伸性能及差異性研究[J].鈦工業進展,2020,37(5):7-11.

復制
分享
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期: 2020-11-09
  • 出版日期: 2020-10-25